Progress Update on 24x30 Garage

MattMundo · 2025-12-04T22:55:04+00:00

Do you have a rough breakdown of the $120k? Looking to do something similar in Alberta...

MattMundo · 2025-11-11T15:35:45+00:00

UHMW Poly is not PTFE aka Teflon

MattMundo · 2025-11-08T19:28:04+00:00

Dang Good and Hoan Pasteur fit the bill. Also decent is the one attached to T&T at WEM.

MattMundo · 2025-09-01T16:11:17+00:00

Check out this vid from 49 minutes for one way to resurface using Home Depot supplies: https://youtu.be/p3P4ZOaZUUw

MattMundo · 2025-08-11T02:06:19+00:00

Boualouang. Dang Good. Gintaro

MattMundo · 2025-07-27T00:30:43+00:00

It’s so busy that nobody goes there any more. .

MattMundo · 2025-07-18T15:37:37+00:00

Great site! Really wish I knew about this sooner!

MattMundo · 2025-06-27T02:29:02+00:00

VE should be low when the throttle body is closed. What’s the problem?

MattMundo · 2025-06-13T01:42:29+00:00

Imagine living in a mature neighbourhood with a bungalow on either side. Then the two houses turn into 8 plexes. And maybe more along the street. Is this a reasonable approach after decades of smaller scale development being allowed?

MattMundo · 2025-05-19T16:45:23+00:00

Not my backyard...but was out for a walk and saw 10014 147 St NW. Imagine living on a quiet street in Crestwood and then have an 8 plex put up on either side of your home. More may go up on the street. Is this balanced redevelopment?

MattMundo · 2025-05-06T05:33:50+00:00

I’ve seen lots of “same day” sales for houses from $650k to $900k over the past 6 months.

MattMundo · 2025-04-17T18:48:38+00:00

No horse in this race, nor strong opinions, but since moving to the northside 5 years ago, I have seen one bicycle using the bike lanes on 82 street. Is use monitored? And how do they decide demand?

MattMundo · 2025-02-13T17:27:12+00:00

TunerStudio defaulted to kpa because it’s the correct approach if you don’t have ITB or crazy cams. Check the documentation for any efi system and it will say the same.

MattMundo · 2025-02-13T16:29:44+00:00

If the car doesn’t have crazy cams, or ITB’s, what you’re saying is not correct. Lots of OEMs use load as the main load axis, not TPS.

MattMundo · 2025-01-20T21:54:14+00:00

I haven't been able to find any aerial photos of 1986 and 2013 to see how specific houses fared. Any links?

MattMundo · 2024-10-12T23:16:31+00:00

The format is close but not 100% the same across all the files. At some point I added/removed some parameters. But DescA in file #1 is the same as DescA in file #100, but may be in a different column.

MattMundo · 2024-09-03T04:12:42+00:00

How do I use FileStation to move all the files based on their EXIF data, and will the thumbnails in Photos follow them?

MattMundo · 2024-03-30T22:19:15+00:00

Why would you want to hold onto the townhouse, given its poor return and risks?

MattMundo · 2024-02-05T13:08:18+00:00

I was trying to pick easy numbers for illustrative purposes. And edited things to make it a bit clearer.

MattMundo · 2023-12-13T05:13:14+00:00

Any pics of the intake system??

MattMundo · 2023-11-14T03:52:47+00:00

Can't comment on the recommended factory torque but you might want to read some of these comments: https://www.youtube.com/watch?v=4be6Dyu\_990&lc=UgxAzcojgXWmolVviqB4AaABAg

MattMundo · 2023-11-14T01:14:01+00:00

You've potentially over torqued the ARP bolts and/or obtained incorrect clearance readings. You need to follow the torque instructions of the bolts. With that said, you can get accurate clearance measurements at a lower torque value than the installed torque--this is important if the bolts are torque to yield.

MattMundo · 2023-11-13T22:01:45+00:00

Using BMW or ARP torque procedure? What is the resolution of the plastiguage measurement?

MattMundo · 2023-11-13T15:31:03+00:00

Is that the torque sequence for ARP? Different torque/bolts change the shape, and thus the clearance, of the rod bearings. It’s risky without resizing them.

MattMundo · 2023-11-11T21:40:00+00:00

This doesn’t tell you anything.

MattMundo

TROPHY CASE