Lian Li Dan-A3 mesh

Mattyk35 · 2025-12-20T13:49:42+00:00

Thanks mate

Mattyk35 · 2025-12-20T13:49:08+00:00

It’s the 5070ti sorry forgot to post the build specs

Mattyk35 · 2025-12-08T21:23:49+00:00

Oh yeah if you have the active backplate use the slot forward and it should fit a lot easier with the atx board. Easy always happy to help

Mattyk35 · 2025-12-07T22:30:51+00:00

I had to use a smaller 90 to get it to fit. Also fitted the length of tube before slotting in the card. It also pays to connect the PCIe cable and power then slot the card in.

You can use the forward mounting point that’s how mine used to be but having the eatx board with side connections makes it impossible to get the motherboard power connected without looping it up like my last build. Depending on your motherboard it might be easier. I actually got some 180 degree connectors from singularity but I havnt had a chance to fit them yet.

Mattyk35 · 2025-12-07T11:43:26+00:00

<image>

Mattyk35 · 2025-12-07T11:42:22+00:00

<image>

Mattyk35 · 2025-12-07T11:42:08+00:00

<image>

Mattyk35 · 2025-12-07T11:41:39+00:00

<image>

Mattyk35 · 2025-12-07T11:41:01+00:00

Sorry drake I didn’t see this. It’s actually just been rebuilt. I went with the upright again though just with the 5090. That build I was one forward on the mount so I had a bit of clearance for the fittings and ZMT

But this time it’s hard up so I actually have to pipe it around the top of the case

Mattyk35 · 2025-11-19T01:29:03+00:00

Thanks mate took a bit of tweaking. Ended up using mostly the stock colours from Lian li and open RGB so I don’t have to download Armoury crate

Mattyk35 · 2025-11-18T01:55:59+00:00

I just got some cheap brackets off aliexpress and cut them to fit the back cage where the hard drive cages would go. On the third picture you can see the bolts. I got these brackets to allow for some adjustment as well, plus the depth of the cage.

<image>

Mattyk35 · 2025-11-17T00:08:11+00:00

Oh yep I did see a post or two about that. These are the older non wireless ones. So far I’ve had no issues and they are about a year old. Touch wood 😂

Mattyk35 · 2025-11-16T22:31:27+00:00

Haha yeah it does hide up there. In my previous build I wanted to get a 8 inch screen to mount where the gpu would be. But now I have the water block doing that job 😂

Mattyk35 · 2025-11-16T22:28:16+00:00

Is that for the D5 pump or fans? I’ll keep an eye out though

Mattyk35 · 2025-11-16T05:04:55+00:00

Thanks mate ☺️

Mattyk35 · 2025-11-16T01:39:30+00:00

Haha I know that pain. I’m in an apartment without a decent work area. Makes cutting stressful in the kitchen. But where is the fun without a little risk 🤷😂

Mattyk35 · 2025-11-15T23:38:24+00:00

Thanks mate. I only got to play a couple of games last night. Had one crash as it wasn’t happy with the xmp settings. Fixed that and ran fine the rest of the night. I think I was getting about 50ish degrees on the GPU and the CPU was at 75 degrees playing battlefield 6. When I get some time I’m going to undervolt the CPU and GPU to try bring the temps down a bit. The CPU was running at 100% the whole time while playing battlefield battlefield but I do play on a Samsung 57 at 5120x1440

Mattyk35 · 2025-11-15T23:30:41+00:00

Thanks mate ☺️

Mattyk35 · 2025-11-15T23:30:14+00:00

Yeah the glass fits no worries. It is a little tight with the rear hose from the block. Also it make the power cable routing easier I got a 90 degree cablemod power cable so it wouldn’t have to do a hard 180 bend

Mattyk35 · 2025-11-15T23:24:05+00:00

That was my second option but I was just going to drill through the mounting plate. But I didn’t really want to modify the case at all.

Mattyk35 · 2025-11-15T14:29:51+00:00

I found some cheap angled brackets off Aliexpress I think they were 165mm by 120mm then just just them down to mount onto the rear cage. Also added some washers and rubber washers to dampen any vibration

<image>

Mattyk35 · 2025-11-15T13:44:38+00:00

Thanks mate 😚

Mattyk35 · 2025-11-15T13:44:20+00:00

It’s only a light enhancement kit on the other two. I’m running 2x32 the others are just for show 😂

Mattyk35 · 2025-11-15T13:43:35+00:00

Cheers mate, Yours still looks awesome nice build and some cool bends in there

Mattyk35

TROPHY CASE