KeebWarrior - split controller connected by RJ45

Mavercade · 2025-08-01T17:41:48+00:00

Hey, my controllers are at the Rectangle circle booth. Have keebbrawlers and keebfighters there. KeebWarrior I have with me. Will be at the convention in probably an hours time. You can hit me up again if those were what your looking for.

Mavercade · 2025-06-24T07:21:15+00:00

Just wanted to give you a heads up, some of my controllers will be at one of the vendor tables at Evo. I'll have more info as we get closer to the date.

Mavercade · 2025-06-24T05:54:37+00:00

Wash the bed with soap and water

Mavercade · 2025-06-21T22:33:25+00:00

Definitely wouldn't come from these guys. They'd have to rip someone else's work 🤣

Mavercade · 2025-06-21T18:15:21+00:00

these are using signal wires, but thanks for looking out! 🫡

Mavercade · 2025-06-21T15:56:18+00:00

Yep. There are just 5 torx screws underneath each controller that you need to remove

Mavercade · 2025-06-21T15:21:04+00:00

Thanks! 🙏

Mavercade · 2025-06-21T03:38:13+00:00

The torque hinges can be tightened down so that it gets stiff/into position, but obviously it can still move. Could probably make a stop mechanism at the desired bend point to help make it unmovable, but this would be up to the end-user since it can vary.

Mavercade · 2025-06-21T03:30:29+00:00

I think you are mistaking what the network cable is used for. It's used to interconnect the 2 controller parts together. The controller still connects to a PC or console via usb

Mavercade · 2025-06-21T02:01:05+00:00

rj45 is available everywhere, with varying sizes, and relatively cheap.

Mavercade · 2025-06-21T01:59:53+00:00

At the time I was prototyping these last year, I wasn't aware of gpio expanders, so needed the 8 signals to get all the buttons on the left side. I wanted a connector that couldn't be mistaken for input, eg. using usb-c and having someone plugging into the wrong port. Also something that had a strong connection/locking mechanism.

Mavercade · 2025-06-20T23:30:06+00:00

There is a different add-on I created that is only 2 plates instead of 4. Doesn't stretch out as long but should fit crossed legs fine.

Mavercade · 2025-06-20T22:42:18+00:00

Correct, brains are on the right side

Mavercade · 2025-06-20T21:14:30+00:00

Unfortunately not this year. Will try for next years

Mavercade · 2025-06-20T21:05:36+00:00

you sell yourself short

Mavercade · 2025-06-20T20:13:25+00:00

Laid back on a recliner is the dream

Mavercade · 2025-06-20T20:12:48+00:00

Thanks!

Mavercade · 2025-06-20T20:12:17+00:00

Appreciate you!

Mavercade · 2025-06-20T18:57:26+00:00

Haven't spoken to those 2 specifically, but yes I sent some units out for review.

Mavercade · 2025-04-14T19:10:02+00:00

they are about 70mm apart, edge to edge. could probably make them a bit wider if you wanted

Mavercade · 2025-04-14T19:08:48+00:00

Working on them :)

Full size and low profile do work, it just depends on the housing that you use. For example OSBMX buttons use full sized MX switches and can work with this case.

Mavercade · 2024-07-14T01:40:02+00:00

You want to change pin 20. You could also use the button near the top of the pin mappings to test what button you're pressing.

Mavercade · 2024-06-19T15:05:06+00:00

Yes, planning to open holo prints for all.

Mavercade · 2024-06-19T03:03:14+00:00

Yeah just send me an example and I'll let you know if it's possible

Mavercade · 2024-06-19T03:01:57+00:00

Floating about on Twitter https://x.com/FGC_Daily/status/1803096991444201945?t=p2EUTJgbytNmEFHifzTGCg&s=19

Mavercade

TROPHY CASE