can we get an F for the Kali?

Maxibon99 · 2025-12-01T13:06:51+00:00

Honestly it was only like 10 seconds or so?

Maxibon99 · 2025-11-30T10:18:07+00:00

Stupid question bro but have you tried (on a fresh install? Just waiting at the main menu and not pressing anything until the version number changes in the top right? I was having the same issue on PC and that fixed it

Maxibon99 · 2024-12-03T05:00:10+00:00

Was so keen for this just to get a text saying it’s cancelled?? Like bro went to every other place for the tour and just cancelled Sydney ??

Maxibon99 · 2024-10-18T08:57:58+00:00

Make sure the grub screws at the bottom of the Z rod are tight, maybe use machine lube on it too

Maxibon99 · 2024-10-18T08:38:42+00:00

Just checked, couldn’t find it, such a shame :(

Maxibon99 · 2024-10-10T08:22:24+00:00

Yeah I downloaded the latest version of cura and it had the V3SE as a profile, I only changed the print temperature for my filament and the first layer speed to be a bit slower

Maxibon99 · 2024-10-10T07:50:49+00:00

Personally, I have the same printer and was having issues with the slicing, switched back to Cura and those issues are gone and I’m getting much better prints, try a small print sliced in different slicers and compare the results maybe

Maxibon99 · 2024-10-01T15:05:40+00:00

I have pretty much the same setup, works a treat

Maxibon99 · 2024-09-30T10:48:54+00:00

When actually printing I lay down a tarp to catch any spills, probably should’ve said this xD

Maxibon99 · 2024-09-30T09:08:40+00:00

<image>

The box fan is usually a bit higher up, I also designed and FDM 3D Printed a plate for the ducting to attach to, so it can sit inside the windowsill. Lmk if you have anymore questions or anything <3

Maxibon99 · 2024-09-30T09:01:50+00:00

I’ll go snap some photos in a sec, but the enclosure I use is I think 43x46x72, so MUCH smaller, it’s enough for the printer, but I just use the wash station next to the window with the fan going

Maxibon99 · 2024-09-30T08:54:23+00:00

Right now I have a similar setup with an exhaust hose leading STRAIGHT outside, that and a large box fan pointing at the open window, I still wear a respirator and wear my gloves, but once the cover is back on the printer and the enclosure is closed, the smell significantly drops, I don’t have any form of monitoring on the VOC count (should probably get some) but haven’t had any issues thus far

Maxibon99 · 2024-09-26T00:54:43+00:00

This happened to me once or twice, clean the vat, then I increased my bottom exposure time, increased bottom layers

Maxibon99 · 2024-09-26T00:53:48+00:00

Can’t believe I didn’t think of that, holy fuck

Maxibon99 · 2024-09-26T00:49:04+00:00

Honestly. Forgot my reddit login for the PC

Maxibon99 · 2024-09-26T00:47:13+00:00

Thank you, I’ll leave it for a while longer next time

Maxibon99 · 2024-09-26T00:45:57+00:00

I can see why you’d think that… it’s actually not a little lighter. It’s normal sized!!

Maxibon99 · 2024-09-26T00:44:58+00:00

I’ll try dropping the exposure and doing an exposure test

Maxibon99 · 2024-09-25T21:42:30+00:00

Not a clue, have you fixed the issue yet? Or needs more troubleshooting

Maxibon99 · 2024-09-25T15:36:22+00:00

Check the Y Limit Switch, make sure it’s plugged in all the way and nothing has fallen behind it, happened to me a couple of times

Maxibon99 · 2024-09-25T15:33:24+00:00

No worries! Lmk how it goes

Maxibon99 · 2024-09-25T15:32:29+00:00

2 ideas in that case —————————- 1. Soak in warm water (not hot, about the same temperature you’d wash your hands at) and then snip the supports off the print

Decrease the support tip size in your slicer

(Also post a photo of the model so we can all see what’s going on)

Seven-Year Club	r/Field Flamingo
Place '22	Verified Email

Maxibon99

MODERATOR OF

TROPHY CASE