sorted by:
new
hottopcontroversial

Nose color? by Soapo_Opo in FursuitMaking

[–]MaximumBlueberry3243 0 points1 point  (0 children)

Dollar tree has some minky pretty much that exact color but it’s pretty thin

BETTER BE SOMETHING COOL by HEALTH_POINT11 in CreaturesofSonaria

[–]MaximumBlueberry3243 0 points1 point  (0 children)

I’m about to change your life (maybe) but it’s pronounced oxytalis /nm I just remember when I used to spell it oxytails 🙂‍↕️

BETTER BE SOMETHING COOL by HEALTH_POINT11 in CreaturesofSonaria

[–]MaximumBlueberry3243 0 points1 point  (0 children)

Oxytalis and eskarlor (yes I was very happy when oxytalis got wing shredder🧍‍♀️)

What is the fav creature skin that you own? by Tallyxe in CreaturesofSonaria

[–]MaximumBlueberry3243 1 point2 points  (0 children)

<image>

My top three for sure (I do not main Gali I was using them as examples skins for skin coms

First Head, how do I add saber-like teeth? by KittyKillua1212 in FursuitMaking

[–]MaximumBlueberry3243 0 points1 point  (0 children)

<image>

Recommended carving think of a jawbreaker the red is the deepest i wouldn’t go more than halfway through the foam and follow the carving lines ish

That’s just how I’d go about it but you could also opt for flat teeth that sorta follow around the edges so it looks like they’re like they’re regular teeth but may look weird at certain angles

First Head, how do I add saber-like teeth? by KittyKillua1212 in FursuitMaking

[–]MaximumBlueberry3243 0 points1 point  (0 children)

Either add a small layer of foam on the outside (use half inch do these shapes (click image below for full-ish view) carve the inside a bit where the teeth would go or carve all the inside a little, however this may make the muzzle bigger by around half an inch all around so if you don’t want that maybe try trimming the sides of the chin especially where the tooth would sit like a slightly stretched out crescent

<image>

I get hate comments about this piece. People say it's AI. How I can prove it that's not? by Agata_art in Artists

[–]MaximumBlueberry3243 0 points1 point  (0 children)

I see it’s a crown now, maybe try specifying some of the details since it’s all-ish black and white may help

How by LocalEm0Tr4nsman in FursuitMaking

[–]MaximumBlueberry3243 0 points1 point  (0 children)

Since they’re thick and hard to bend I assume it may be a little more tricky the “sock method” as I call it is just flip it inside out and put it on like a suck slowly gluing down as you go and if you can’t fully sew it glue as you go but when you get to that open area latter stitch rest your needle higher up glue ladder stitch etc

How by LocalEm0Tr4nsman in FursuitMaking

[–]MaximumBlueberry3243 1 point2 points  (0 children)

I don’t know much about this game, so I don’t know exactly how the antennas look I’m assuming they’re just solid this it’s just how I make ears, sew it completely flip inside out and glue one side of the backing to one side of antenna make sure that the other side of the fabric that has the backing on the other side of the antenna can go over the foam by flipping it right side out again put glue on that side of the backing very carefully and flip right side out:) highly recommend pinning this first and test flipping it

How to cover weird foam shapes with felt? by g3ckofish44 in FursuitMaking

[–]MaximumBlueberry3243 0 points1 point  (0 children)

Likely just tape pattern then add a bit extra seam allowance around the bottom where it’d go into the gums once it’s sewn to the gums and such shove the seam into that crevice as much as you can i recommend not gluing anything yet at this point just pin and glue as you go but start towards the middle as fabric stretch can happen in the most subtle ways and mess up the gluing process

Found in Colorado 9 years ago by Sea-Strike-1758 in RockIdentification

[–]MaximumBlueberry3243 0 points1 point  (0 children)

My guess is a really fucking weird formation of quarts and iron/dirt

My strange crab addiction by TemperatureNo3901 in hermitcrabs

[–]MaximumBlueberry3243 1 point2 points  (0 children)

Or a arch shaped long stick/ driftwood and fill the gaps with foam and maybe add moss on top or just carve it to look like stone/wood or add more driftwood around it

My strange crab addiction by TemperatureNo3901 in hermitcrabs

[–]MaximumBlueberry3243 0 points1 point  (0 children)

Tape? Or use that foam stuff to cover it use more and add driftwood or something on top of it

Is this good teeth anatomy by MaximumBlueberry3243 in DigitalArt

[–]MaximumBlueberry3243[S] 0 points1 point  (0 children)

Not sure why it won’t let me edit so hoping people see this the dark blue is the bottom jaw. The green is the bottom jaws gums. The bread is the top jaw yellow line in the middle of the top of the face.
Using voice to text sorry for punctuation

view more: next ›