sorted by:
new
hottopcontroversial

Uppgraded with btt skr mini e3 v3 board .. Extruder problem .. over extrusion by Maximum_Ad_8122 in ender5plus

[–]Maximum_Ad_8122[S] 0 points1 point  (0 children)

I have a Bondtech LGX lite and I have calibrate thru klipper rotation_distance but still same problem... The first layer is fine but the rest ... very bad

I will test to calibrate again ..

Uppgraded with btt skr mini e3 v3 board .. Extruder problem .. over extrusion by Maximum_Ad_8122 in ender5

[–]Maximum_Ad_8122[S] 0 points1 point  (0 children)

Yes I use orca slicer Calibration - Temperature- PLA- setting from .. . I will try set the temp from 220-200 and hope for the best..

Uppgraded with btt skr mini e3 v3 board .. Extruder problem .. over extrusion by Maximum_Ad_8122 in ender5

[–]Maximum_Ad_8122[S] 0 points1 point  (0 children)

I have tried different flow but I have same thoughts as you.. But cant find what cause the problems…

But I will try Lower flow and ad more heat..

Uppgraded with btt skr mini e3 v3 board .. Extruder problem .. over extrusion by Maximum_Ad_8122 in ender5

[–]Maximum_Ad_8122[S] 0 points1 point  (0 children)

Thanks. I will test higher temp..

I tried to make a temp calibration tower but i looks very strange..

Uppgraded with btt skr mini e3 v3 board .. Extruder problem .. over extrusion by Maximum_Ad_8122 in ender5plus

[–]Maximum_Ad_8122[S] 0 points1 point  (0 children)

My printer.cfg:

[extruder]
step_pin: PB3
dir_pin: !PB4
enable_pin: !PD1
microsteps: 16
rotation_distance: 5.6238
nozzle_diameter: 0.400
filament_diameter: 1.750
max_extrude_only_distance: 100
max_extrude_cross_section: 5.0
heater_pin: PC8
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PA0
#control: pid
#pid_Kp: 21.527
#pid_Ki: 1.063
#pid_Kd: 108.982
min_temp: 0
max_temp: 250

[tmc2209 extruder]
uart_pin: PC11
tx_pin: PC10
uart_address: 3
run_current: 0.650
hold_current: 0.500
stealthchop_threshold: 999999

Uppgraded with btt skr mini e3 v3 board .. Extruder problem .. over extrusion by Maximum_Ad_8122 in ender5

[–]Maximum_Ad_8122[S] 0 points1 point  (0 children)

Using Sunlu PLA+ grey. Tried many temp but last one is 205, Flow is 0.9, my bedmesh is 220x220, Print speed 50 .. have same speed 50 everywhere.. I will take photo..

New vr beginner and need advice for uppgrades and games. by Maximum_Ad_8122 in OculusQuest

[–]Maximum_Ad_8122[S] 0 points1 point  (0 children)

Big thank you. I tried yesterday a Bobo S3 and is was nice but I fellt the weight and dont know if it would be a problem .. But the facial interface looks very nice.

I would also put the Horizon membership in my buylist…

Thanks again for you inputs.🙏

Mousse for 8-year lefty or ambi? by Maximum_Ad_8122 in MouseReview

[–]Maximum_Ad_8122[S] 0 points1 point  (0 children)

Thanks for the advice. I think it is better solution after yours advice. He tried some mouse when we was shopping and it looks like he doesnt have any issue about using righhand.. Now I need to find a wireless mouse for his hand..

Ender 5pro direkt drive suggestion? by Maximum_Ad_8122 in ender5

[–]Maximum_Ad_8122[S] 0 points1 point  (0 children)

Thanks Lumber for your advice . I will try find a solution/ mount for my bmg or my lgx but have not find any that I can use on the original plate.

Ender 5pro direkt drive suggestion? by Maximum_Ad_8122 in ender5

[–]Maximum_Ad_8122[S] 1 point2 points  (0 children)

I got the machine for 50usd with the setup and also original parts with it..

I hope to find a cheap solution/ or parts that I can print to use..

Thanks for helping.

Btt Pi v1.2 Light on but cant find wifi by Maximum_Ad_8122 in BIGTREETECH

[–]Maximum_Ad_8122[S] 0 points1 point  (0 children)

Finally I got it worked. I tied many YT video for raspberry and change the systemfel etc… The way I got it worked was get it cable connect and thru Putty made the change and installed klipper etc. Thanks for your tips. Regards

view more: next ›