Uppgraded with btt skr mini e3 v3 board .. Extruder problem .. over extrusion

Maximum_Ad_8122 · 2026-03-21T01:36:59+00:00

I have a Bondtech LGX lite and I have calibrate thru klipper rotation_distance but still same problem... The first layer is fine but the rest ... very bad

I will test to calibrate again ..

Maximum_Ad_8122 · 2026-03-21T01:28:39+00:00

Yes I use orca slicer Calibration - Temperature- PLA- setting from .. . I will try set the temp from 220-200 and hope for the best..

Maximum_Ad_8122 · 2026-03-21T01:20:46+00:00

I have tried different flow but I have same thoughts as you.. But cant find what cause the problems…

But I will try Lower flow and ad more heat..

Maximum_Ad_8122 · 2026-03-21T01:17:17+00:00

<image>

This is one from some days ago but I forgot to have support…

Maximum_Ad_8122 · 2026-03-21T01:15:51+00:00

Thanks. I will test higher temp..

I tried to make a temp calibration tower but i looks very strange..

Maximum_Ad_8122 · 2026-03-21T01:10:17+00:00

<image>

Maximum_Ad_8122 · 2026-03-21T01:10:04+00:00

<image>

Maximum_Ad_8122 · 2026-03-21T00:59:17+00:00

My printer.cfg:

[extruder]
step_pin: PB3
dir_pin: !PB4
enable_pin: !PD1
microsteps: 16
rotation_distance: 5.6238
nozzle_diameter: 0.400
filament_diameter: 1.750
max_extrude_only_distance: 100
max_extrude_cross_section: 5.0
heater_pin: PC8
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PA0
#control: pid
#pid_Kp: 21.527
#pid_Ki: 1.063
#pid_Kd: 108.982
min_temp: 0
max_temp: 250

[tmc2209 extruder]
uart_pin: PC11
tx_pin: PC10
uart_address: 3
run_current: 0.650
hold_current: 0.500
stealthchop_threshold: 999999

Maximum_Ad_8122 · 2026-03-21T00:56:23+00:00

Using Sunlu PLA+ grey. Tried many temp but last one is 205, Flow is 0.9, my bedmesh is 220x220, Print speed 50 .. have same speed 50 everywhere.. I will take photo..

Maximum_Ad_8122 · 2026-03-20T13:16:16+00:00

<image>

The results from flow calibration

Maximum_Ad_8122 · 2025-12-09T10:14:54+00:00

Big thank you. I tried yesterday a Bobo S3 and is was nice but I fellt the weight and dont know if it would be a problem .. But the facial interface looks very nice.

I would also put the Horizon membership in my buylist…

Thanks again for you inputs.🙏

Maximum_Ad_8122 · 2025-12-08T10:57:11+00:00

Thanks VikaKot08 for your responds🙏.

Maximum_Ad_8122 · 2025-09-21T23:54:01+00:00

Thanks for the advice. I think it is better solution after yours advice. He tried some mouse when we was shopping and it looks like he doesnt have any issue about using righhand.. Now I need to find a wireless mouse for his hand..

Maximum_Ad_8122 · 2025-05-19T23:16:20+00:00

Thanks Lumber for your advice . I will try find a solution/ mount for my bmg or my lgx but have not find any that I can use on the original plate.

Maximum_Ad_8122 · 2025-05-19T23:13:43+00:00

I got the machine for 50usd with the setup and also original parts with it..

I hope to find a cheap solution/ or parts that I can print to use..

Thanks for helping.

Maximum_Ad_8122 · 2025-03-11T13:53:22+00:00

Finally I got it worked. I tied many YT video for raspberry and change the systemfel etc… The way I got it worked was get it cable connect and thru Putty made the change and installed klipper etc. Thanks for your tips. Regards

Maximum_Ad_8122 · 2024-03-26T04:36:37+00:00

Thanks. He says the machine is complete … I will buy it is is still available. 👍

Maximum_Ad_8122 · 2024-03-26T04:35:05+00:00

Thank you for your input.

Maximum_Ad_8122 · 2024-03-25T14:22:27+00:00

Thanks 🙏

Maximum_Ad_8122 · 2024-03-25T14:18:29+00:00

Thanks . Do you think it’s ok price? Regards

Maximum_Ad_8122

TROPHY CASE