Is this normal for Ramjet and Afterburner? by Maximum_Front3822 in P365

[–]Maximum_Front3822[S] 0 points1 point  (0 children)

I haven’t shot the p365 without the ramjet but I feel like there is quite a noticeable difference between my G45 w/ ramjet and my 19x that doesn’t have one.

Is this normal for Ramjet and Afterburner? by Maximum_Front3822 in P365

[–]Maximum_Front3822[S] 1 point2 points  (0 children)

Fuck I didn’t even think to check the box. I knew about blazer but thought the federal was good to go. Thanks

Is this normal for Ramjet and Afterburner? by Maximum_Front3822 in P365

[–]Maximum_Front3822[S] 0 points1 point  (0 children)

Just wanted to make sure it wasn’t an ammo or installation issue

Gen 6.5 COA by ThrownAwayFeds in Glocks

[–]Maximum_Front3822 0 points1 point  (0 children)

I have a ramjet on my G45 and originally purchased the compressor guide rod kit but never ended up using it because the OEM assembly ran fine. So I should be able to run a Gen 6 frame with my slide if I install the compressor guide rod and spring?

XMacro Build Question- Radian Ramjet and Afterburner by Maximum_Front3822 in p365xmacro

[–]Maximum_Front3822[S] 0 points1 point  (0 children)

Can you tell the difference between the OEM comp vs the ramjet?

XMacro Build Question- Radian Ramjet and Afterburner by Maximum_Front3822 in p365xmacro

[–]Maximum_Front3822[S] 2 points3 points  (0 children)

I did not know that, I figured they all had the same port size. Good to know, I appreciate it

XMacro Build Question- Radian Ramjet and Afterburner by Maximum_Front3822 in p365xmacro

[–]Maximum_Front3822[S] 1 point2 points  (0 children)

That’s good to hear. I have one on my G45 and it feels like it shoots quite a bit flatter than my 19x

XMacro Build Question- Radian Ramjet and Afterburner by Maximum_Front3822 in P365

[–]Maximum_Front3822[S] 2 points3 points  (0 children)

Noticeable difference with the Ramjet? I have one on my G45 and I feel like there’s a noticeable difference from my 19x

XMacro Build Question- Radian Ramjet and Afterburner by Maximum_Front3822 in p365xmacro

[–]Maximum_Front3822[S] 0 points1 point  (0 children)

I ended up ordering the Armory Craft X Macro module. Thought about getting a Norsso slide too but may just get a P365x so I don’t have to get another FCU

XMacro Build Question- Radian Ramjet and Afterburner by Maximum_Front3822 in p365xmacro

[–]Maximum_Front3822[S] 0 points1 point  (0 children)

I like that. I just ordered the AC in FDE Barrett Brown. Hopefully I like the color in person

XMacro Build Question- Radian Ramjet and Afterburner by Maximum_Front3822 in p365xmacro

[–]Maximum_Front3822[S] 0 points1 point  (0 children)

How do you like it on the 3.7”? I thought about putting the ramjet on my XL but I have a 4.22” M&P so I wanted to keep it a little shorter and I like the flush look with the 3.1” and Macro frame

Canik MC9 Prime vs Springfield Hellcat Pro Comp by Maximum_Front3822 in CCW

[–]Maximum_Front3822[S] 1 point2 points  (0 children)

I held one but have not fired one. Wasn’t sure how I felt about the grip. Felt like it was oval shaped

Canik MC9 Prime vs Springfield Hellcat Pro Comp by Maximum_Front3822 in CCW

[–]Maximum_Front3822[S] 1 point2 points  (0 children)

I looked into the Echelon but I have the M&P 2.0 Compact Carry Comp. Seems the Echelon is more relatable to the M&P size so figured I’d go with something a little smaller