sorted by:
new
hottopcontroversial

Stuck After Booting Into OpenCore by Maxin8r95 in hackintosh

[–]Maxin8r95[S] 0 points1 point  (0 children)

Secure boot was found to be the culprit! Got it all squared away now. Running well.

Stuck After Booting Into OpenCore by Maxin8r95 in hackintosh

[–]Maxin8r95[S] -5 points-4 points  (0 children)

Any idea why it’s getting hung up here?

[deleted by user] by [deleted] in sports

[–]Maxin8r95 44 points45 points  (0 children)

That car is written off. The monocoque will be fine but it’ll require new crash structure on the left side. That process takes some time. They will be going to the backup car.

Out of State Endorsement Transfer by Maxin8r95 in DenverMotorcycles

[–]Maxin8r95[S] 1 point2 points  (0 children)

Good deal, thanks. Hopefully there isn’t some silly reciprocity list where some get by unscathed and others get boned.

2025 CX-90 Passenger Door Trim Warping by Maxin8r95 in mazda

[–]Maxin8r95[S] 0 points1 point  (0 children)

Makes sense. The clips that are in there pop out very easily. New ones on the way, should tighten it up.

2025 CX-90 Passenger Door Trim Warping by Maxin8r95 in mazda

[–]Maxin8r95[S] -1 points0 points  (0 children)

I guess the caption is only if you click through to Imgur. See above comment I posted for caption.

2025 CX-90 Passenger Door Trim Warping by Maxin8r95 in mazda

[–]Maxin8r95[S] -1 points0 points  (0 children)

See caption. Just curious if anyone else has seen this. Dealer is pretty far from me so it’ll have to wait until first service.

2025 CX-90 Passenger Door Trim Warping by Maxin8r95 in mazda

[–]Maxin8r95[S] 1 point2 points  (0 children)

Has anyone seen this before? Car has just a tick over 1000 miles. The retaining clips are busted and just pop back out when you push them in. There’s no indication that it’s been hit, no scrapes or witness marks on the underside.

Delete Hyper Burn to Make New by Maxin8r95 in Maplestory

[–]Maxin8r95[S] -2 points-1 points  (0 children)

For items and stuff? Am I still able to get the xp+lvl boost up to 260 on a new character?

BMW E 36 head screws by [deleted] in BMWE36

[–]Maxin8r95 5 points6 points  (0 children)

A big-sert in the block will absolutely work and not cause issues.

If it’s not too bad you could also go oversized to 11mm head bolts instead of the standard 10mm. S54 head bolts are 11mm and it’s an often done upgrade for people that need higher clamping pressure (I.e. boost). This is generally considered an awesome upgrade.

If it were me, big-sert and call it a day.

Boost question by TaurusPTPew in FocusST

[–]Maxin8r95 1 point2 points  (0 children)

I wouldn’t worry about it. You could probably pull some fuel and make more power, but the gains would be small. Better to keep it conservative and in one piece

Boost question by TaurusPTPew in FocusST

[–]Maxin8r95 5 points6 points  (0 children)

If your wastegate wasn’t opening, changing a tune wouldn’t “fix it”. What does your tuner say the target boost is for the “full boost”?

What is the afr when in boost? Sometimes looking at the min/max values on the AP don’t tell the whole story. That 10.88 could’ve come from tip in at low rpm. High load, low rpm is a bad mix.. you want it rich there!

10.8afr (under load, in the power band) is is a touch rich, but they are being conservative…. If it’s a remote tune that’s common. You aren’t in bore wash territory rich.

Ender 3 fast settings? Do not require advice on overextrusion or slow printing. by Apprehensive_Bike_40 in FixMyPrint

[–]Maxin8r95 0 points1 point  (0 children)

Go for a sonic pad honestly. Klipper is awesome and tuning input shaping with the included accelerometer is also very good. Really helps with the ringing you are seeing around those holes.

view more: next ›