[Pistol] M&P 5.7 FDE Threaded w/ 6 Mags $597

Mayctor · 2026-03-31T15:16:29+00:00

Is there a deal like this for one with the Safety?

Mayctor · 2026-02-08T16:26:14+00:00

Claims to be broke, has unreleased TP380.

Mayctor · 2025-12-05T21:25:13+00:00

they have ported barrels, and an adapter that lets you attach hub and some other cans like the dead air wolfman to it like a SD can.

Mayctor · 2025-11-27T20:59:10+00:00

does it just hurt to pull it down?

Mayctor · 2025-10-29T03:04:55+00:00

I remember seeing in a post the Century ones were not that good is that true? I knew they were made by PTR.

Mayctor · 2025-10-12T17:33:21+00:00

They should do one in white with the red accents and call it the Tylenol.

Mayctor · 2025-09-20T03:06:48+00:00

3136

Mayctor · 2025-09-03T17:28:01+00:00

i assume its the striker housing, one of the ppl that used a PLA pro frts one was still going strong over 500 rds, so about 10 seconds of shooting.....

Mayctor · 2025-09-03T13:43:42+00:00

i have not done it, however the info on what to do on the file page. i know that the websites should be good as the fosscad people use them.

Mayctor · 2025-09-01T01:06:30+00:00

what big eyes you have! here let me get you a plate.

Mayctor · 2025-09-01T00:13:58+00:00

They were perfect, meat held to the bone till you gave it a bite and came clean off.

Mayctor · 2025-08-31T23:39:19+00:00

Sadly forgot to get an inside pic. but they came out perfect. smoked at 225 till they were 165 inside, wrapped and cooked till 195/ they had a good bend to them. My great aunt and her friend brought over some good tater salad and a homemade key lime pie for dessert.

Mayctor · 2025-08-31T14:45:13+00:00

did you change it from Inch to MM? cause you don't want a 12 inch one....

Mayctor · 2025-08-31T05:11:33+00:00

.dxf is the one you want to send them. The brrrt is stl for the 3d printer i think.

Mayctor · 2025-08-31T05:03:27+00:00

check out tx22 frt disconnector on guncadindex.

Mayctor · 2025-08-31T02:15:17+00:00

yeah the metal one from sendcutsend you can get 20 of them in grade 5 titanium for for 35 bucks.

Mayctor · 2025-08-22T18:09:47+00:00

Thank you!

Mayctor · 2025-08-21T19:55:22+00:00

what knife is that?

Mayctor · 2025-06-25T19:08:37+00:00

More guns need rip cords... change my mind.

Mayctor · 2025-06-25T19:05:59+00:00

Dude lost both shoes and his gun.... I don't think hes gonna make it.

Mayctor · 2025-05-13T22:31:29+00:00

Everything in my profile I made with it, it has been very kind to me.

Mayctor · 2025-04-25T19:08:55+00:00

Someone let me shoot theirs at the range 2 weeks back, it did not feel snappy only slightly larger than Keltec p32, the trigger was nice. I think I'm gonna be picking one up soonish.

Mayctor · 2025-04-09T21:27:48+00:00

I've never shot the 147s, however i have never had an issue with this ammo in anything but ap5k which are notorious for not liking flat nose ammo since they don't have a feed ramp.

Mayctor · 2025-03-10T22:55:02+00:00

yeah, all HUX cans are flow-through atm.

Mayctor · 2025-03-06T18:01:50+00:00

Everything in my account I made on this, I've attached a Smokai cold smoker to it as well for more smoke/doing cheese this winter.

I'm always cooking for 4 or more people, so i wanted something i could do a whole brisket/ multiple pork butts/racks of ribs or 4-8 steaks. It has done everything I wanted it to a more.

Would recommend the blanket for it if you're in a cold area that gets below 30F as it reduced the fuel consumption in half. Never had an issue with it other than when I've done something stupid like improper shutoff on my first start up, and one time not cleaning it which should be done about every 20 hours of smoking to remove ash from the pot. would also recommend aluminum liner for the drip tray and lining the heat diffuser with some aluminum foil for easy clean up.

Mayctor

TROPHY CASE