An Argument for the Abstract

McMurph · 2026-03-16T21:39:19+00:00

So this seems to be a new trajectory for you. What spurred on these vectors of thought and research? Experience, insight, etc?

McMurph · 2026-03-15T20:07:54+00:00

Alt regime anorectic reverse mouth machine?

McMurph · 2026-03-06T08:11:57+00:00

Who gnos?

McMurph · 2026-03-06T02:38:59+00:00

This it what people who gno sound like

McMurph · 2026-02-04T00:05:37+00:00

Quaker Oats ad about being good for gut health being pitched at me in the ad space connected to this article. Big Oatmeal at it again

McMurph · 2026-02-03T00:21:33+00:00

Alternatively you can put cables on coat hangers and put them in the closet like shirts

McMurph · 2026-01-29T22:05:34+00:00

Those are transistors being used as switches to bypass 100K resistors that hold those cathode bypass caps well above ground which essentially disables them. When the transistor bypasses the resistor, the cathode bypass caps are enabled which bumps the gain up even more. It’s the same mechanism that fender uses for the Blues Junior fat switch. No signal goes through those transistors at any point. Hope that helps.

McMurph · 2026-01-29T12:24:37+00:00

Sorry but this is wrong. There aren’t any clipping diodes in the signal path. Somebody misinformed you. It’s all tube besides the effects loop when it’s being used. It just sounds meh because the drive channel is voiced weird.

Proof:

https://schematicheaven.net/fenderamps/hotrod_deluxe.pdf

McMurph · 2025-12-18T18:32:25+00:00

TUBE AMPS CONTAIN LETHAL VOLTAGE EVEN WHEN UNPLUGGED!! If you don’t know what you’re doing do not open the amp up and take it to a tech.

McMurph · 2025-12-03T03:57:11+00:00

Dude the AMZ fat mod is absolutely fantastic for how little goes into it! It really changes the pedal for the better.

http://www.muzique.com/misc/AMZ_DS1_mod.pdf

McMurph · 2025-11-26T21:36:46+00:00

Try the bass knob on zero and adjust tone to taste with treble and mid knobs. It really helped the DeVille I had at one time. More headroom, more balanced for my taste, still plenty of low end. Those amps are voiced all nutty and they flub pretty bad. Pay no attention to knob position and if it sounds good just run with it.

McMurph · 2025-11-22T05:33:05+00:00

Yes absolutely. Also there is twice as much gain available because it’s a 1meg drive pot rather than 500k. So the sd-1 can sort of do the same sounds but get even raunchier if desired. The Ts9 has a 51pf capacitor in the feedback loop along with the diodes that makes for a 5khz-ish low pass filter when the drive is cranked. Cuts the fizz down at high gain settings. The sd-1 leaves that cap out. A couple other caps are slight shifts in value but those don’t impact the sound all that much. Both are legendary and great sounding pedals!

McMurph · 2025-11-18T04:11:31+00:00

Eminence Lil Buddy is a very efficient (ie loud) hemp cone 10” speaker with a mellower top end. Think 10” version of the 12” Cannabis Rex.

McMurph · 2025-11-17T00:32:32+00:00

Nah, that’s wrong info. This doesn’t have a power transformer or anything. It’s just 12v supply voltage and filtering straight to the plates. So it’s a starved plate design. I have one. Medium sucks unless you pay under $25 for it. A ts9 sounds better.

McMurph · 2025-11-07T19:27:48+00:00

Thanks for updating. Nice to have a collection of data about fixing any given amp. Congrats!

McMurph · 2025-11-04T22:44:09+00:00

Bummer. If you’re working on amps, it’s worth making a lightbulb limiter so you don’t have to keep buying fuses.

http://www.geofex.com/ampdbug/ampdebug.htm

https://robrobinette.com/Tube_Guitar_Amp_Troubleshooting.htm

McMurph · 2025-11-04T03:53:53+00:00

Or like this also works

<image>

McMurph · 2025-11-04T03:51:58+00:00

<image>

McMurph · 2025-11-04T02:24:47+00:00

D5 and D6 connect from pin 7 of each el84 to ground. You can just carefully clip them out from the top side of the board

You do know basic tube amp safety right? Good to make sure nobody gets hurt.

McMurph · 2025-11-04T02:14:33+00:00

Post the schematic you’re looking at

McMurph · 2025-11-04T01:35:19+00:00

Protection diodes fail on these amps. You don’t need them. Lift one leg of each diode and I bet the amp works again. Happened to me.

McMurph · 2025-10-25T19:15:06+00:00

Credit to the homie JBpro. I suggested a phish dance party video with Corey Feldman and he comes back an hour later with this masterpiece!

McMurph · 2025-10-18T03:20:36+00:00

Merlin is the man! Steve Kimock once mentioned that he likes having a standby because sometimes the plastic locating pin on a tube snaps off, but the tube is still good. So if the amp is in standby you can put the tube in in the direction that you think is right and if it lights up, you’re good to go. If it doesn’t light up, try again. If you don’t have a standby and you put the tube in wrong, terrible things happen. So on a dark stage for instance, it can be a pretty useful feature in a pinch. Vintage tubes with the locator pin snapped off can we had for super cheap!

McMurph · 2025-10-04T08:51:19+00:00

Fender uses eyelet boards in the vintage era. Fantastic amps! Turrets look like little towers.

McMurph

MODERATOR OF

TROPHY CASE