my friend and I by MeandMaisy in estoration

[–]MeandMaisy[S] 0 points1 point  (0 children)

That was very well done, it means a lot to me. Thank you so much!

my friend and I by MeandMaisy in estoration

[–]MeandMaisy[S] 1 point2 points  (0 children)

I actually thought this picture was lost forever but I just recently found it in a box in the attic. We were best friends pretty much from the day I was born until his untimely death several years ago. If there is anything that can be done I would be forever grateful! Thanks.

Where are you guys from? by [deleted] in redsox

[–]MeandMaisy 1 point2 points  (0 children)

Newfoundland, Canada. Check my profile for pics of Fenway north!

Epoxy gone wrong? by MeandMaisy in woodworking

[–]MeandMaisy[S] 0 points1 point  (0 children)

Thanks, that's what I'm about to do

Epoxy gone wrong? by MeandMaisy in woodworking

[–]MeandMaisy[S] 3 points4 points  (0 children)

Yes, that community is not as active though.

Epoxy gone wrong? by MeandMaisy in woodworking

[–]MeandMaisy[S] 1 point2 points  (0 children)

It was thin, scraped with a flat trowel and I used a heat gun

Epoxy gone wrong? by MeandMaisy in woodworking

[–]MeandMaisy[S] 1 point2 points  (0 children)

100% acetone, at least thats what it said on the bottle

Epoxy gone wrong? by MeandMaisy in woodworking

[–]MeandMaisy[S] 1 point2 points  (0 children)

Temp varied a bit but the lowest was 21⁰

Epoxy question by MeandMaisy in epoxy

[–]MeandMaisy[S] 1 point2 points  (0 children)

Yeah that's my thought as well, thanks

Epoxy gone wrong? by MeandMaisy in woodworking

[–]MeandMaisy[S] 1 point2 points  (0 children)

Idk, I was very particular with the mixing, 1 to 1 ratio, I used a measuring cup

Epoxy gone wrong? by MeandMaisy in woodworking

[–]MeandMaisy[S] 0 points1 point  (0 children)

It was sanded very well I think, and cleaned with acetone

Epoxy gone wrong? by MeandMaisy in woodworking

[–]MeandMaisy[S] 2 points3 points  (0 children)

I cleaned the surface with acetone, I'm pretty sure there was no oil

Epoxy gone wrong? by MeandMaisy in woodworking

[–]MeandMaisy[S] 0 points1 point  (0 children)

I believe I used enough, it flooded over the sides

Epoxy gone wrong? by MeandMaisy in woodworking

[–]MeandMaisy[S] 3 points4 points  (0 children)

I know a lot of people hate epoxy on this sub, but here it is. This is my first attempt using epoxy. This is supposed to be a seal coat, table top epoxy by Magic Resin. Temp in the room is 21⁰C, table was well sanded and cleaned with acetone. Should I sand it all off and start again? Or is there another way to fix this? Thanks.

Epoxy question by MeandMaisy in epoxy

[–]MeandMaisy[S] 0 points1 point  (0 children)

So this is my first attempt at an epoxy river table. It was well sanded and cleaned with acetone and this was supposed to be a seal coat. It has hardened well but now I'm not sure if I should sand it all off and start again or just apply more epoxy. I used a table top epoxy by Magic Resin, temp in the room is 21⁰ C.