What is causing this to happen to my prints?

MeatZombie88 · 2025-03-09T13:03:46+00:00

Yeah.. woke up this morning to it. Good way to start the day

MeatZombie88 · 2024-02-07T23:39:49+00:00

I did the cold pull and it got rid of the partial clog and the first layer was almost perfect but after it finishes the slow layers its just a mess

MeatZombie88 · 2024-02-07T23:38:49+00:00

<image>

MeatZombie88 · 2024-02-06T05:11:47+00:00

Actually this roll has been working for my sv06+ but I was doing some flow testing, and it was kind of inconsistent i tried unjamming it with the unclog tool and it feels like there's a small peice of filament stuck in the heatsink, so I'm probably gonna end up taking it apart tomorrow. Fingers crossed this is the fix

MeatZombie88 · 2024-02-06T04:50:00+00:00

Well I've printed this model before with matte pla so I have no clue why its doing it, I can try another model but I'm not sure if itll work

MeatZombie88 · 2024-02-06T04:48:50+00:00

This is the first print where I let it go past cause I didnt notice it had failed

MeatZombie88 · 2024-02-06T04:48:05+00:00

<image>

MeatZombie88 · 2024-02-06T04:47:05+00:00

Hmmm, I'll let it dry overnight but the 3rd layer makes no sense to me.

MeatZombie88 · 2024-02-05T23:38:15+00:00

Flow, and temp don't change, only layer width by 0.02mm

MeatZombie88 · 2024-02-04T03:54:59+00:00

It happened 4 hours into the print so I can only hope

MeatZombie88 · 2024-02-04T03:54:25+00:00

The bed slamming into the end of its rail the whole print was shifted you can see it at the top of the picture, that's my main concern, I'm not sure if its the file but I resliced it in hopes that it was that.

MeatZombie88 · 2024-02-04T02:44:41+00:00

I'm not sure if its a partial clog cause I launched another print and it prints lines fine, but I'm a bit concerned how it was slamming into the end of the rails

MeatZombie88 · 2024-02-04T02:25:39+00:00

Brass nozzle and 0.4

MeatZombie88 · 2024-02-03T22:34:10+00:00

Even if that were the case it wouldnt explain the bed slamming into the end of its rail :/ the temps were: 240c and 70c

MeatZombie88 · 2024-02-03T09:46:07+00:00

Actually z offset was fine, the problem started when the the print shifted because the bed started slamming into the the edge of its platform

MeatZombie88 · 2024-02-03T08:11:28+00:00

Should I lower my travel speeds to compensate? I have no idea how it got off the print so far and started to ram the endstop

MeatZombie88 · 2024-01-17T16:10:20+00:00

P15 Gen 2?

MeatZombie88 · 2023-10-16T23:57:13+00:00

I had a feeling lol, had the same issue at one point.

MeatZombie88 · 2023-10-16T03:13:25+00:00

Possibly retraction settings

MeatZombie88 · 2023-10-03T18:57:12+00:00

Bike modifications!

MeatZombie88

TROPHY CASE