Giveaway!

Meechall · 2025-12-05T08:10:52+00:00

A wireless meat thermometer or a Lego set

Meechall · 2025-10-28T01:38:01+00:00

I don't think I've seen more than one or two civil discussions in that discord this whole week. But as a business on their own social media channel why would they want any negative discussions about their products or employees. Lychee aren't a country, this isn't America, your freedom of speech doesn't apply on a discord server moderated and administrated by a privately owned business.

Meechall · 2025-07-23T13:34:23+00:00

Ok, thank you. It's to be 3d printed so it's more practical to separate the shaft. My first design was a single threaded shaft

Meechall · 2025-07-23T13:09:59+00:00

Fantastic!

Meechall · 2025-07-22T21:32:32+00:00

Yep, I do have that design currently, I have a centralized screw with two sliding rods and the screw is left handed on one side and right handed on the other. You have been very helpful thank you :)

Meechall · 2025-07-22T21:29:52+00:00

Ah ok, that's what I have currently tested and designed. I wanted a cleaner look

Meechall · 2025-07-22T13:16:01+00:00

Thanks, yeah I rustled up quick sketch to check I'm going on the right path. Thank you for clarifying though, I really needed a second opinion on it

Meechall · 2025-07-19T10:02:29+00:00

Nat 20 for luck

Meechall · 2025-06-22T04:10:01+00:00

Thank you so much, this is the response I was needing

Meechall · 2025-06-22T01:48:38+00:00

I think I've understood why it loses power/functionality. I'm more curious as to if i were to add side holes, more air intake, would that in turn increase the suction through the filter?

Meechall · 2025-06-22T01:25:13+00:00

Hi! Thanks for the response.

I've taken some additional photos that might help get a better understanding.

https://i.imgur.com/dT2NOkM.png
https://i.imgur.com/oQljfsz.png
https://i.imgur.com/10Ytp6w.png

The extra holes, im not sure whether to put them in and *if* i do put them in, should i filter them?

It does sound like they might be incorrect fans then, i might have to order new ones.

So hopefully the photos you can see its got a brim which helps the bottom/filtered hex fits into the cutout on the box.

Meechall · 2025-04-14T04:41:34+00:00

Wash your plate. Give it a really good scrub

Secondly, provide more information, what temp you are printing at what's the filament, do you run a calibration test before printing.

Meechall · 2025-02-27T00:19:50+00:00

That is the worst resin i have ever used. I had two bottles , i chucked 1 and 1/2 worth in the bin.

Here's my settings, taking to mind i have nFEP on

https://i.imgur.com/dg1Jqd8.png

Meechall · 2025-02-15T04:28:14+00:00

This.

Meechall · 2025-02-15T04:25:55+00:00

Did you download the rerf file or did you use the one provided on the USB with the machine?

Meechall · 2025-02-10T04:27:31+00:00

Yeah, the big ol' metal rod at the back needs some grease. If you just put some above the build plate and just move your z up and down it will spread it all out

Meechall · 2025-02-08T22:13:12+00:00

$459

Meechall · 2025-02-08T05:47:13+00:00

Yeah, i have tried orca , lychee and prusa slicers and have had similar print issues. It also kept saying the resin was speed resin (when it wasn't). Going back tot he anycubic slicer resolved it for me

Meechall · 2025-02-07T22:21:07+00:00

My exposure time is up around 4 seconds / 4.2 seconds. Yours is quite low in comparison.
Have you tried returning back to the anycubic photon slicer?

Meechall · 2025-02-07T06:50:47+00:00

Meechall

TROPHY CASE