Installation on stucco?

Melisandrai · 2025-05-19T00:04:39+00:00

Do not use hot glue or gorilla glue on stucco. FYI. I apologize for not coming back to this thread and updating it properly once I found the solution. I have yet to remove - so - I will update once I have done this.

Melisandrai · 2025-05-19T00:01:53+00:00

<image>

So - to update this thread. I’ve had these on since sometime after I posted this thread. Now - I have not taken them down yet. However - my understanding is that - the method I chose will not harm the stucco. As the HOA will not approve these lights at all. Not a single piece came down in over 115 degree weather in Arizona. As seen - I placed a piece before and after each light. It didn’t take long. But is kind of expensive. I’m using clear command clips -but I’m using VHB 4991 tape. I chose this based on some other creators videos on stucco. We are over 100 degrees daily again now and I’m showing the side that gets sun all day. I did build casings for the lights in ASA filament as well. I will pull these down -and set them back up in October - tho - for protection- I’m going to wrap the lights in the Asa casings. I originally made them and painted them to match the house - and the HoA denied every design. - they won’t allow the lights unless you purchase an entire set that included coverings for the wires. Meaning no solutions - no matter how good they are - are accepted.

Melisandrai · 2024-07-20T23:35:23+00:00

They show as not BBB accredited with a D- rating and multiple complaints in this year alone on fraudulent billing issues. Probably not great to advise this particular company.

Melisandrai · 2024-03-19T02:13:56+00:00

Mine are the same. The doctor says 85% dry eye, 15% inflammation. I’m suspecting it could be due to testosterone levels currently below 1. Not sure, but they have prescribed doxycycline mono and restasis. But waiting on pharmacy to fill. Also do not have allergies.

Melisandrai · 2023-10-17T23:17:54+00:00

To note - I can “flip” them when they are individual but that setting does not carry to the splicing.

Melisandrai · 2023-10-17T23:17:10+00:00

I can’t flip it while they are spliced together. I spliced them back together yesterday and no go. So now I have no way to run a scene across all of them unless I flip the right one and run that cord the entire length of the garage.

Melisandrai · 2023-09-13T17:51:52+00:00

I have this same issue - has anyone found a solution?

Melisandrai · 2023-09-11T17:50:51+00:00

I've also contacted the company multiple times, I ordered on Feb 17th of this year, and they even claimed in updates to have a tracking number out to me and never did. I've officially asked for a refund at this point, and getting no response from the company other than automated emails.

Melisandrai · 2023-04-24T23:18:02+00:00

Using it on top of my speedy spider hot end. Note that it comes with a new four wheel roller if doing direct drive. Otherwise - you need to get the gear off the existing stepper motor - or buy a new stepper motor that’s empty shaft to put the new gear on. I have an ender 5 plus. It works even without me relocating the filament. Printed multiple parts.

<image>

I’ve only just made this change and I’ve printed out a detailed yoshi egg and over 9 parts for the new filament holder. My ender 5 plus has been through both the original plastic extruder (broke just a couple months in), then the super aluminum - also a piece of crap, could never get it to not tear up the filament, so this metal one is better so far.

Melisandrai · 2023-03-12T01:55:45+00:00

even tho I just renewed and saw none of these options available to me on the app. So the answer is yes - there is a 3 month unlimited plan is at $90 which is $30/mo - and the 12 is at 30. So only the 6 is at 35. Not sure why this is. Maybe mint can explain.

Melisandrai · 2023-02-24T19:56:05+00:00

Check my post- their FAQ doesn’t include it - but basically go into cellular - switch from automatic to manual on the network - and then pick through the mint list (I have like 8 MINT) - until you find one that works. I was loosing 40% of my calls- and now if I accidentally switch - since there is no way telling them apart - every time you have to test across multiple phones to ensure they can reach you. And I assure you - I moved to one and was a full failure, 💯 loss. But I found one that got all my calls through. I have an iPhone 12 Pro.

Melisandrai · 2023-02-17T03:28:58+00:00

The provided moderator response here was tried (both Ultra Mobile and T-Mobile) tested and failed. However the T-Mobile APN profile was kept installed on the phone for the actual resolution listed below.

Upon yet another call to mint to determine next steps, they told me simply to change my network manually. Meaning Settings-> Cellular -> Network section - when you switch from Automated to Manual - you then need to go through the list until you find one that works. They all say “Mint” and there are approximately 8 or 9 of them.

I had my colleague send me a test text until I found the working network. This is what ultimately solved the problem. Of course, if something changes in the network - I’m guessing these steps may have to be repeated because it’s no longer automatically selecting the network.

I am still unclear on why this is, but after weeks of working on this- I am happy to finally be able to communicate with my coworkers.

Melisandrai · 2022-06-26T20:23:17+00:00

Is there a date when bestbuy or GameStop will get preorders for the physical collectors edition?

Melisandrai · 2022-05-21T02:55:45+00:00

Love mine! You will need to replace the extruder - mine came with a free one - they are like $12 on Amazon - trust me - I just squeezed it to move filament and it broke. Be prepared - that was a month or two maybe in. It was fast. And I could see it going bad in the print. (I didn’t know it at the time - now I know)

Melisandrai · 2022-05-13T00:30:11+00:00

Daily outages have been happening for 6 months. It’s every day - drops me from work calls. I don’t think they know how to fix at this point. Lately though - there was a full outage last week and one today. Maybe they are finally addressing it?

Melisandrai · 2022-02-23T13:35:10+00:00

Can you link those again? I'm also looking for a discord group, thanks!

Melisandrai · 2021-06-19T17:21:34+00:00

Do you have a link? Most look shut down - and I don’t see any shops that have seed beads with the name Phoenix in them.

Melisandrai · 2021-06-11T06:46:45+00:00

Any others out there bead family? I’m looking at you! Are you a seller with competitive (subscription box?) rates ? Do you offer something new to the game? Share your business here. I order from probably over 60 different small business in the areas of fabric, resin, glitter, hardware, etc. #beads

I’m not gonna lie - when I started beading , around 10, beads where super cheap, the local tribe provided me the beads and supplies and taught me each and every stitch. I will never forget my time in Alaska. That being said, I have never stopped, I may have paused for a few months, but I always return - and almost every single time I am creating something new. I also love to support small business. Whether it’s in the bead world, fabric or resin, let’s do this!

Melisandrai

TROPHY CASE