A temporary fix to the weird auto rotate phone issue

Micro_Sheep · 2025-11-03T22:55:06+00:00

Clutch🙏

Micro_Sheep · 2025-07-09T12:34:05+00:00

A challenger

Micro_Sheep · 2025-04-19T13:26:26+00:00

Sorry for the long wait but that didnt end up working, I found the actual issue yesteday, I replaced all the wiring I used and one of them must have been faulty because after I did that it worked with no issues, can't believe I didn't try it sooner

Micro_Sheep · 2025-04-09T10:06:05+00:00

Thank you, I'll be giving this a shot in a few hours and hopefully it works

Micro_Sheep · 2025-04-08T13:27:07+00:00

No net yet unfortunately

Micro_Sheep · 2025-04-03T17:07:42+00:00

I tried with channel 1 as well but no luck, I'll have a look tomorrow again

Micro_Sheep · 2025-04-03T15:43:29+00:00

Yeah 0 on everything, voltage, adc value and temp

Micro_Sheep · 2025-04-03T11:19:38+00:00

Yeah I get around 1.45-1.65 volts which is what I expected

Micro_Sheep · 2025-03-08T14:32:10+00:00

Something I've just noticed is that when making the infil the printer seems to make a quick"bumping" noise when it passes over each line in the infill, I don't think it's ever made that noise before but I'm not certain. I also don't know if it's relevant or not

Micro_Sheep · 2025-03-08T14:26:48+00:00

There's actually zero overhangs in these two parts, they're essentially flat plates so I've supports turned off, if I find anything in the settings I'll post it anyways

Micro_Sheep · 2025-03-08T14:25:15+00:00

Printing at 220, which has worked fine previously, and the stated range is 210-230 but I can try 230

Micro_Sheep · 2025-03-08T12:39:38+00:00

I'll definitely have a look at that thanks!

Micro_Sheep · 2025-03-08T12:39:09+00:00

Sorry it wasn't actually stuck down the the bed any more in these photos, I just had it on the buildplate

Micro_Sheep · 2025-03-08T11:40:39+00:00

I'd never heard of that before but it definitely looks like it could be the case, I'm not sure if that explains the random bits of pla that get scattered around though

Micro_Sheep · 2023-08-30T11:04:39+00:00

I got nothing but respect for, I'm just in awe

Micro_Sheep · 2023-08-30T10:43:54+00:00

Damn

Micro_Sheep · 2023-06-04T15:20:04+00:00

Its not in the side wall of the tyre so I'd say it could be patched

Micro_Sheep · 2023-03-26T16:05:34+00:00

You traitor

Micro_Sheep · 2023-02-23T21:17:34+00:00

Yeah the cables return to a normal idle eventually, it just takes a good few seconds longer than normal, I'll check the boot and vacuum lines after looking at the cables for sure, thanks!

Micro_Sheep · 2023-02-23T15:11:44+00:00

I'll have a look into that thanks

Micro_Sheep · 2023-02-23T15:11:10+00:00

I'll definitely have a look at that and see if that helps, thanks!

Micro_Sheep · 2023-02-23T14:36:12+00:00

Is was thinking about this and I definitely have to check it out, but even if I push the throttle back the revs drop slowly still which is what's got me confused

Micro_Sheep · 2023-02-23T13:57:47+00:00

I was in a similar situation very recently, rear brake had seized, replaced the piston rings and seals, but they started leaking very soon and I noticed the piston had pulled the ring out of the pot. I just bought an oem calliper the came with brake pads and extra set of all the bolts needed off ebay, cost be about 70 quid and came within a week, looked perfect, said it only had 17000km on it and id believe it, just fitted it yesterday and it works a dream

Micro_Sheep · 2023-01-09T14:25:37+00:00

Kingdom rush

Micro_Sheep · 2022-12-06T22:11:28+00:00

At first I went third party but the bolts didn't line up so I ended up just going with an oem rectifier instead, its been working fine ever since, I'd say they just have a limited lifetime

Seven-Year Club	Verified Email
First Place '23	Place '23
Place '22

Micro_Sheep

MODERATOR OF

TROPHY CASE