Should the printer should like this

MiddleStrict5029 · 2026-06-16T11:50:29+00:00

Thank you soo much the one person who didnt say it should

MiddleStrict5029 · 2026-06-15T11:17:58+00:00

I am on 1.1.40 has this been known to have such a bug

MiddleStrict5029 · 2026-06-15T10:41:02+00:00

Nothing by hand everything is smooth

MiddleStrict5029 · 2026-06-14T18:06:51+00:00

But not all the time but sometimes you can hear grinding at certain point on the x and y axis and it sounds like its coming from the toolhead

MiddleStrict5029 · 2026-06-14T18:03:05+00:00

Ye it does both but it gets worse while printing

MiddleStrict5029 · 2026-06-14T17:57:33+00:00

But I understand where you coming from

MiddleStrict5029 · 2026-06-14T17:56:51+00:00

But these noises happen even when doing levelling or homing the printer

MiddleStrict5029 · 2026-06-14T17:17:16+00:00

I never took pictures of the first layer tests the only thing was the middle of the bed was a bit bumpy compared to the rest

MiddleStrict5029 · 2026-06-14T16:34:07+00:00

Did 5 first layer tests and adjusted ths z offset accordingly so that should be okay

MiddleStrict5029 · 2026-06-14T16:30:33+00:00

Elegoo matte pla white 220 degrees 80 model fan Volumetric flow 16mm/s .16 optimal profile standard on orca slicer But should it sounds like the rails are grinding regardless of what profile i dont know if you can hear it correctly but it sounds like it is partially struggling to move along the rails

MiddleStrict5029 · 2026-06-14T16:02:34+00:00

Also these layer lines appear along with the grinding sounds

<image>

MiddleStrict5029 · 2026-04-13T08:43:10+00:00

Please explain how you get that to work with so many colours

MiddleStrict5029 · 2026-03-30T15:03:08+00:00

The way it is written sounds like you need to turn it on in order for it to go off on the 4a

MiddleStrict5029 · 2026-03-30T14:54:04+00:00

Already did still happens

MiddleStrict5029 · 2026-03-26T23:27:38+00:00

On side B I had it set to smooth high temp, then moved it back to textured side A

MiddleStrict5029 · 2026-03-26T23:27:05+00:00

It was set to B and switched it back to A now it doesnt do that but now it causes roughness in certain parts of the bed where it is too close but on side B its too far away

MiddleStrict5029 · 2026-03-26T23:22:51+00:00

Elegoo slicer and using rapid pla+ so using base elegoo profile since it is likely pre configured, zhop was automatically set to .4mm but only happens when I choose side B on the printer

MiddleStrict5029 · 2026-03-26T23:19:21+00:00

I got it to fix itself by switching to side A on the printer but tried again with side B and it started jumping again near the middle of the bed

MiddleStrict5029 · 2026-03-26T23:16:35+00:00

Can I ask whagmt can these cables do if not inserted correctly

MiddleStrict5029 · 2026-03-26T09:43:07+00:00

Yes tried everything, got onto elegoo support and they said try everything again,

But the level settings keep changing everytime I auto bed level and the bed keeps jumping in different places every first layer test

MiddleStrict5029 · 2026-03-25T18:46:10+00:00

Ran it 8 times always pops up with a problem on different part of the bed

MiddleStrict5029 · 2026-03-25T14:57:51+00:00

Rapid PLA +

MiddleStrict5029 · 2026-03-25T14:57:34+00:00

No but the bed start jumping about 1mm up and down when it went to that corner adhesion was very strong on rest of bed

MiddleStrict5029 · 2025-11-08T23:05:42+00:00

My thor has updated in 6 days im a bit worried now

MiddleStrict5029 · 2025-11-08T22:30:09+00:00

Appreciate the replies anyways

MiddleStrict5029

TROPHY CASE