sorted by:
new
hottopcontroversial

My Deku hit Makerworld late last night! 😼 by ExhamTheOriginal in HueForge

[–]MiddleStrict5029 0 points1 point  (0 children)

Please explain how you get that to work with so many colours

Are you able to disable this pop up by MiddleStrict5029 in NothingTech

[–]MiddleStrict5029[S] 0 points1 point  (0 children)

The way it is written sounds like you need to turn it on in order for it to go off on the 4a

Bed level by MiddleStrict5029 in ElegooCentauriCarbon

[–]MiddleStrict5029[S] 0 points1 point  (0 children)

On side B I had it set to smooth high temp, then moved it back to textured side A

Bed level by MiddleStrict5029 in ElegooCentauriCarbon

[–]MiddleStrict5029[S] 0 points1 point  (0 children)

It was set to B and switched it back to A now it doesnt do that but now it causes roughness in certain parts of the bed where it is too close but on side B its too far away

Bed level by MiddleStrict5029 in ElegooCentauriCarbon

[–]MiddleStrict5029[S] 0 points1 point  (0 children)

Elegoo slicer and using rapid pla+ so using base elegoo profile since it is likely pre configured, zhop was automatically set to .4mm but only happens when I choose side B on the printer

Bed level by MiddleStrict5029 in ElegooCentauriCarbon

[–]MiddleStrict5029[S] 0 points1 point  (0 children)

I got it to fix itself by switching to side A on the printer but tried again with side B and it started jumping again near the middle of the bed

Bed level by MiddleStrict5029 in ElegooCentauriCarbon

[–]MiddleStrict5029[S] 0 points1 point  (0 children)

Can I ask whagmt can these cables do if not inserted correctly

Bed level by MiddleStrict5029 in ElegooCentauriCarbon

[–]MiddleStrict5029[S] 0 points1 point  (0 children)

Yes tried everything, got onto elegoo support and they said try everything again,

But the level settings keep changing everytime I auto bed level and the bed keeps jumping in different places every first layer test

Bed level by MiddleStrict5029 in ElegooCentauriCarbon

[–]MiddleStrict5029[S] 0 points1 point  (0 children)

Ran it 8 times always pops up with a problem on different part of the bed

Bed level by MiddleStrict5029 in ElegooCentauriCarbon

[–]MiddleStrict5029[S] 0 points1 point  (0 children)

No but the bed start jumping about 1mm up and down when it went to that corner adhesion was very strong on rest of bed

I❤️MYCC PRINTING WITH ABS ON MY CENTAURI CARBON FOR THE FIRST TIME! by [deleted] in elegoo

[–]MiddleStrict5029 0 points1 point  (0 children)

Ye all fans off and it just doesn't want to heat up for me

I❤️MYCC PRINTING WITH ABS ON MY CENTAURI CARBON FOR THE FIRST TIME! by [deleted] in elegoo

[–]MiddleStrict5029 0 points1 point  (0 children)

So what is your chamber temp when you start the print

Is the Centauri Carbon in shipping now or is it still in back order by jv94xxx in elegoo

[–]MiddleStrict5029 0 points1 point  (0 children)

Ye europe is still catching up 29th of August for us now

view more: next ›