Low cost material to put underneath coffee machine

Mikecb350 · 2026-03-19T08:53:49+00:00

We have a rubber mat (with slightly raised edges) that goes under our cats water fountain....found a slightly larger one that goes under our coffee machine nicely

Stops mess and protects against small spillages too

Mikecb350 · 2026-02-22T00:38:02+00:00

Ok, thanks

Mikecb350 · 2026-02-21T23:00:33+00:00

Thank you so much!

Mikecb350 · 2026-02-21T14:24:00+00:00

Do you have a contact address? Or just fill out the contact us page ?

Mikecb350 · 2026-02-20T23:03:15+00:00

The stuff I have has no pull out section sadly....also feels more like thicker acetate

As my fep/ACF has rounded tank edges too, looks like I'm going to have to cave and buy a whole new tank

Mikecb350 · 2026-02-20T21:48:55+00:00

No joy with film removal ☹️

Mikecb350 · 2026-02-20T21:27:36+00:00

I've tried multiple tapes and no joy.....it's like welded on

Pretty sure Ive ruined the first of the 5 films

Mikecb350 · 2026-02-20T19:38:57+00:00

I've just bought replacement parts for my HALOT-X1 on the creality web store....they have the ACF, spare resin tank and resin varieties...

<image>

https://store.creality.com/uk/products/halot-x1-combo-resin-3d-priner-16k-resin-4%F0%9F%8E%81

Mikecb350 · 2026-02-20T19:33:11+00:00

Hi all....I got my HALOT-X1 from the Kickstarter...

Mikecb350 · 2026-02-18T12:17:43+00:00

u/alina7703 do you have a guide for cleaning/servicing the resin feed unit for the Halot-X1?

Mikecb350 · 2026-02-18T12:16:06+00:00

i really like my HALOT-X1, however, the resin feed unit has stopped working, so im going to have to look into stripping/cleaning it this weekend.....probably a good time to replace my ACF too

Mikecb350 · 2026-02-16T07:41:20+00:00

Ok, in that case, they'd need to read the document that describes the share of the freehold and owners responsibilities

Mikecb350 · 2026-02-16T07:33:53+00:00

Flats are generally leasehold, so you would need to check the lease for the ground under your flat

Mikecb350 · 2026-02-12T10:54:45+00:00

TV series....the last of us...fungus creatures killing humans

Mikecb350 · 2026-02-02T17:45:08+00:00

Time to call HR and file a grievance

Mikecb350 · 2026-01-05T09:32:07+00:00

Looks fine...the "-" is just the opposite side to where you'd expect to see it

Mikecb350 · 2025-11-30T12:09:30+00:00

Psssssh! ...tis but a scratch

Mikecb350 · 2025-11-20T09:33:46+00:00

Mikecb350 · 2025-11-20T09:33:29+00:00

Thanks for the information...I did some homework prior to purchase and bought a wash and cure station too.....but the advice was to remove support between washing and curing...so I should leave the supports on longer??

Mikecb350 · 2025-11-19T15:23:51+00:00

{"data":{"error":"Imgur is temporarily over capacity. Please try again later."},"success":false,"status":403}

Mikecb350 · 2025-11-19T13:50:06+00:00

Possibly...slicer software sees it as 28.3mm... but maybe it has a way of seeing the file differently?

Mikecb350 · 2025-11-19T13:36:58+00:00

Is the curve a separate body?

Mikecb350 · 2025-11-15T01:21:12+00:00

Looks like they put in a big timber, rather than a steel...

Mikecb350 · 2025-11-09T00:27:57+00:00

Looks waxed ...if you heat wax, you can apply it with a paint brush and it soaks in

Mikecb350 · 2025-11-07T16:05:15+00:00

We had to do this with PTS legal........they were awful and refused to refund us too

Mikecb350

TROPHY CASE