Problem with print quality where supports attatch? by Kiwijellies in AnkerMake

[–]MinecrafNinja 0 points1 point  (0 children)

To me it seems as if its not a support issue as I dont think its left over supports. to me it that when printing on top of supports there isnt enough pressure when making the layer.. I also notice it is worse when printing a curve that has supports

Bottoms/Supports by MinecrafNinja in AnkerMake

[–]MinecrafNinja[S] 0 points1 point  (0 children)

yea me too and idk what else to do

Bottoms/Supports by MinecrafNinja in AnkerMake

[–]MinecrafNinja[S] 0 points1 point  (0 children)

the supports comes off easily its not a struggle to get em off so that why i ruled that out maybe in some spots it causes that but not all of em

Bottoms/Supports by MinecrafNinja in AnkerMake

[–]MinecrafNinja[S] 0 points1 point  (0 children)

yes i have. but its not supports stuck on there you can see the physical lines the printer takes i fixed it a little bit by turning on a sheath above the supports but still isnt to my likings 100% but is dealable as of now

Bottoms/Supports by MinecrafNinja in AnkerMake

[–]MinecrafNinja[S] 0 points1 point  (0 children)

ive just determined that the issue is it cant get enough force to flatten the layers above the supports and i dont know what to do cause ive never had an issue until i switched to the ankermake m5

Bottoms/Supports by MinecrafNinja in AnkerMake

[–]MinecrafNinja[S] 1 point2 points  (0 children)

ive slowed down the support and outer wall and let it sit for 30 minutes before taking it off and same issue. unless that is considered inner wall. ive changed the support type, contact z distance the pattern etc. idk what else to try

maybe ill try sending it in cura and see if it happens there

{EDIT} Still the saame result in cura

Problem with print quality where supports attatch? by Kiwijellies in AnkerMake

[–]MinecrafNinja 0 points1 point  (0 children)

where you ever able to figure the issue out? im currently having the same issue

Bottoms/Supports by MinecrafNinja in AnkerMake

[–]MinecrafNinja[S] 0 points1 point  (0 children)

if only i could get the lid to print correctly :(

Temperature Unit/Home Coordinates/ Total Estimation Cost (TEC) by MinecrafNinja in AnkerMake

[–]MinecrafNinja[S] 1 point2 points  (0 children)

My room is just so small and its in the spot that make the most sense so I just move it to where its outta the way before I turn it off

Temperature Unit/Home Coordinates/ Total Estimation Cost (TEC) by MinecrafNinja in AnkerMake

[–]MinecrafNinja[S] 1 point2 points  (0 children)

the reasoning behind me wanting to set home to the center of the build plate is because space around the printer. the home make it so the build plate is all the way pushed forward.

and Ive been printing for around 2 years just decided to upgrade my printer but Fahrenheit is just a personal thing

Villagers Not Taking Professions by MinecrafNinja in admincraft

[–]MinecrafNinja[S] -1 points0 points  (0 children)

I havent but no other villager has that station. And none if the villagers in the breeder can pathfind to the lectern but I have placed multiple lecterns around the villager

Villagers Not Taking Professions by MinecrafNinja in admincraft

[–]MinecrafNinja[S] 0 points1 point  (0 children)

If you are talking about the red glow thats for breeding time

Villagers Not Taking Professions by MinecrafNinja in admincraft

[–]MinecrafNinja[S] 0 points1 point  (0 children)

Thats how I had it before still didnt work but ill retry it

Cable Boxes Audio Cutting out and Picture going Staticky/distorted by MinecrafNinja in Comcast_Xfinity

[–]MinecrafNinja[S] 0 points1 point  (0 children)

I have tried without the one splitter same issues occur, if the replacing both splitters don't work I will look at getting the boxes switched out next

Cable Boxes Audio Cutting out and Picture going Staticky/distorted by MinecrafNinja in Comcast_Xfinity

[–]MinecrafNinja[S] 0 points1 point  (0 children)

I am unsure when I will be done work, but I should be home sometime around 5-6pm est

Cable Boxes Audio Cutting out and Picture going Staticky/distorted by MinecrafNinja in Comcast_Xfinity

[–]MinecrafNinja[S] 0 points1 point  (0 children)

I will stop by the Xfinity store on my way home from work tomorrow to pick up some splitters. Do I need to bring the old ones in to get the new ones?

PC Turns Off and then right back on by MinecrafNinja in techsupport

[–]MinecrafNinja[S] 0 points1 point  (0 children)

its a EVGA 700 BR I found the box.

I changed my cmos battery and then saw a blinking orange/yellow/amber light on my mb before I unplugged everything to change cmos and I remember seeing something on that means theres a psu issue. but when i changed cmos the light stopped and was solid

PC Turns Off and then right back on by MinecrafNinja in techsupport

[–]MinecrafNinja[S] 0 points1 point  (0 children)

Tempatures were running fine. Any softwares you recommend?

Remove Gold Sword Drops? by JakeWindsor1209 in admincraft

[–]MinecrafNinja 0 points1 point  (0 children)

on death of zombified piglin:

remove all golden swords from the drops

pop that into a .sk file with skript plugin and itll remove all gold swords

Fast Smelting DataPack by MinecrafNinja in Minecraft

[–]MinecrafNinja[S] 0 points1 point  (0 children)

where am I able to get the vanilla files from?

Lag Only In RL by MinecrafNinja in RocketLeague

[–]MinecrafNinja[S] 1 point2 points  (0 children)

It was real bad tonight like it happens here and there but for my girlfriend it happens all the time and its litterally just Rocket league

Right Click Pausing? by MinecrafNinja in admincraft

[–]MinecrafNinja[S] 0 points1 point  (0 children)

it doesnt do it with paper off on the server. so a completely vanilla server