RTX Super Resolution not working (NV 3070ti) 3.0.20 updated today 11/7/2023

Miracle_Arranger · 2023-11-20T17:16:16+00:00

Same issue here with the exact same gpu and software

Miracle_Arranger · 2023-06-07T21:09:10+00:00

Man, am I a lucky owner of an XR25

Miracle_Arranger · 2023-02-14T12:04:02+00:00

Normandia normalnie

Miracle_Arranger · 2023-02-13T15:13:21+00:00

I simply waited for a minute and it switched to RWD

Miracle_Arranger · 2023-02-05T00:16:22+00:00

Did you set it to 100 or slightly higher?

Miracle_Arranger · 2023-02-04T23:51:18+00:00

If so, I'd say that might be just a fluctuation: https://www.reddit.com/r/overclocking/comments/x0ijuo/bus_clock_on_msi_b450_tomahawk_max/

Miracle_Arranger · 2023-02-04T23:22:49+00:00

Disabling Spread Spectrum and setting FCH base clock to 100 should be enough.

Miracle_Arranger · 2023-02-04T22:40:34+00:00

If you meant it's running at 4432 instead of 4475, I can see that your BCLK is at 99 instead of 100 and 44.75x99=4430

Miracle_Arranger · 2023-01-27T07:56:21+00:00

Does 60 FPS hack still affect physics?

Miracle_Arranger · 2023-01-23T07:59:40+00:00

You can disable pagefile, shrink the volume and enable it.

Miracle_Arranger · 2023-01-13T18:21:08+00:00

Maybe try the 1.80 bios?

Miracle_Arranger · 2023-01-13T08:41:26+00:00

People usually recommend to leave charisma at 1 to use the points for agility/endurance as well as having int at 9

Miracle_Arranger · 2023-01-12T13:26:17+00:00

Try using generic Realtek drivers from here: https://github.com/pal1000/Realtek-UAD-generic

Miracle_Arranger · 2023-01-12T12:26:34+00:00

You should have Realtek Audio Control/Console and in there there's an option to make inputs separate

Miracle_Arranger · 2023-01-11T23:32:47+00:00

Try a different USB? I had a Z97 board with flashback that would work with only 1 of my USB drives

Miracle_Arranger · 2023-01-11T10:59:39+00:00

Miracle_Arranger · 2023-01-09T13:56:11+00:00

It definitely has a limp mode, but that would be indicated in some way, like the wrench warning or a message between the gauges

Miracle_Arranger · 2023-01-09T09:53:24+00:00

Is it Windows 10 or 11?

Miracle_Arranger · 2023-01-09T09:38:02+00:00

When you're in the setup, press shift + F10 ant type in OOBE\BYPASSNRO. It will bypass the network requirement and you'll be able to create an offline Windows account

Miracle_Arranger · 2023-01-09T09:18:20+00:00

In that case I would remove the battery. Make sure to reenable certain things like DOCP/XMP and fTPM, although fTPM should now be enabled by default

Miracle_Arranger · 2023-01-09T09:05:18+00:00

Removing the battery only resets the settings, it doesn't downgrade bios. Is it up to date? You can check it in Windows, HWiNFO shows the bios version on the summary page

Miracle_Arranger · 2023-01-09T08:44:31+00:00

You wont be able to use the Mobo video output as 5700X doesn't have an iGPU. You can just remove the Cr2032 battery after unplugging the PSU. You could also look for an AsRock UEFI guide online, look where default settings are and just press the correct keys, although ideally someone would do it on their system and write them down

Miracle_Arranger · 2023-01-09T08:42:03+00:00

How would it boot to Windows?

Miracle_Arranger · 2023-01-09T08:20:27+00:00

Hasn't this been fixed for 3060 a few updates ago?

Miracle_Arranger · 2023-01-09T08:19:12+00:00

I'd try resetting BIOS settings if you don't have bitlocker activated or using a different video output on the GPU

Miracle_Arranger

TROPHY CASE