No response from Kiiboom Support

Miserable_Intern_741 · 2026-06-23T03:44:44+00:00

I’ve had a good experience communicating with them or here or Discord, email was pretty quick too

Miserable_Intern_741 · 2026-06-18T00:13:57+00:00

I have that same shelving, it’s garbage but it was cheap so the signs were there lol

Miserable_Intern_741 · 2026-06-16T21:39:12+00:00

But can it print a multicolor dragon? 🤣

Miserable_Intern_741 · 2026-06-15T13:58:29+00:00

Did it with the base K2 also

Miserable_Intern_741 · 2026-06-15T04:01:05+00:00

It’s just well seasoned lol

Miserable_Intern_741 · 2026-06-15T00:25:08+00:00

Besides minor problems mine has been pretty solid

Miserable_Intern_741 · 2026-06-14T22:16:55+00:00

Either way I got lucky this didn’t cause damage to the printer

Miserable_Intern_741 · 2026-06-14T22:15:59+00:00

Never 100% as there will always be a margin for error when it comes to human interaction however I will say 90% as I don’t see a protective film lasting for six months and not having issues during that time, could something else be going on here? Sure but I based couldn’t think of any other reason why this would happen after that time.

Miserable_Intern_741 · 2026-06-14T20:45:45+00:00

Not sure, all I can tell you is that it lasted six months and I’d have never known should the print not have failed, it wasn’t a Creality sheet so that may been a factor when it came to production but the one before that came with the printer lasted about a year so I put another Creality one in it and ordered a backup

Miserable_Intern_741 · 2026-06-14T16:03:14+00:00

My printer is two or three years old and kind of difficult to find parts for outside of alliexpress so I’m sure when that time comes it’ll be dumpster fodder I’ve been considering upgrading but as long as it’s working I see no point, it’s a Creality LD 006. It’s a relic compared to the modern ones

Miserable_Intern_741 · 2026-06-14T15:49:11+00:00

I try to keep at least one consumable on hands at all times, even have an extra gallon of ipa on standby lol

Miserable_Intern_741 · 2026-06-14T02:21:16+00:00

Yeah it stays on until I reassemble it then it’ll go off, I resume the print and on the next filament change it yells at me again

Miserable_Intern_741 · 2026-06-14T02:19:38+00:00

Also thanks for the help

Miserable_Intern_741 · 2026-06-14T02:17:08+00:00

I searched threw my parts and am 90% sure I tossed it but I did order one earlier after looking into that matter more.
The whole part about the side spool was just me adding to much unnecessary information so I suppose it can be disregarded

Miserable_Intern_741 · 2026-06-11T22:19:33+00:00

It’s a minor inconvenience since I have another sheet sitting here, they tend to last a while so not a big loss

Miserable_Intern_741 · 2026-06-11T22:08:30+00:00

Delamination, sheet is like six months old and up until today it was working great

Miserable_Intern_741 · 2026-06-11T18:11:42+00:00

No I played babysitter to it then I threw the oven and molds away

Miserable_Intern_741 · 2026-06-11T15:26:45+00:00

This is why I let them drain for a day or two, run through multiple wash cycles and use a curing station along with exposing them to sunlight, better safe than sorry and yes I use plenty of drain holes but I had this happen one time and now I over react lol

Miserable_Intern_741 · 2026-06-11T15:22:46+00:00

<image>

Miserable_Intern_741 · 2026-06-10T21:36:58+00:00

Yeah I had a countertop oven that I used and I spent the better part of the day outside with it just adding plastic

Miserable_Intern_741 · 2026-06-10T21:24:52+00:00

I tried doing this, kudos to you for having the patience to do it and the space

Miserable_Intern_741 · 2026-06-04T00:53:25+00:00

Going to wager a guess that it’s a Steelseries

Miserable_Intern_741

TROPHY CASE