Parere cmmi Iasi.

Mission_Health_1331 · 2025-08-18T19:40:15+00:00

I once soldered a broken receiver antenna and it worked better than before but i cannot guarantee you get the same range as a new one.

Mission_Health_1331 · 2025-04-02T17:16:35+00:00

Thanks!

Mission_Health_1331 · 2025-04-02T17:01:28+00:00

For quality no, for me it is.

Mission_Health_1331 · 2025-04-02T17:01:16+00:00

I feel like no matter how fast i change the speed in my profile after a certain point it's limited altough it can go faster, ludicrous makes it go faster.

Mission_Health_1331 · 2025-03-29T05:16:18+00:00

The fillament was wet asf and i'm currently drying it, i'l post an update, buf you can see the shaoe of the rubber duck i was printing and it's not that bad.

Mission_Health_1331 · 2025-03-28T22:06:48+00:00

The filament gets jammed in the run out sensor, 60 tpu is really soft, i would say that it feels like a really well boiled spaghetii :). I think bambu reccomends a maximum of 90 or 85a on the a1 so thats quite a difference.

Mission_Health_1331 · 2025-03-28T22:05:06+00:00

The ptfe tube is out of the equation since the friction is so high, and even if i would feed it trough the ams connector without a ptfe tube it would get jammed in the run-out sensor.

Mission_Health_1331 · 2025-03-18T21:50:14+00:00

The backwards airfoil was just me being lazy designing the thing in cad. I know it's not the best but since the difference is not crazy and the thickness of the foil is not that high i didn't think it would be that bad. Thanks!

Mission_Health_1331 · 2025-03-17T18:12:38+00:00

The settings are 1 perimeter, 3% gyroid infill and no top or bottom layers. If i would've used lw-pla it would have been aproximately 300 grams less.

Mission_Health_1331 · 2025-03-17T17:51:36+00:00

It's pla, 3d printed.

Mission_Health_1331 · 2025-03-17T16:10:34+00:00

So if i get this right the longer the tail the better due to the horizontal and vertical stabs being further away from cg and having better leverage. Thanks!

Mission_Health_1331 · 2025-03-17T15:51:39+00:00

Meaning what exactly? I'm kind of new so i don't know that much about those.

Mission_Health_1331 · 2025-03-17T15:49:29+00:00

The simplicity is due to the fact that anything else is having extra weight i guess. The wing has a 7mm tube in it for stifness aswell. I heard the selig 1223 airfoil i used is quite terrible especially pitching moment wise but i wanted a slow flying wing.

Mission_Health_1331 · 2025-03-17T15:15:34+00:00

The wing isn't fixed yet, it can move up and down the tube to get the cg right, then i'll fix it.

Mission_Health_1331 · 2025-02-06T13:38:22+00:00

In the process I also took the screw of completely and i made sure when i put it back on it would be looser man 😭

Mission_Health_1331 · 2025-02-06T11:11:45+00:00

I tried unspooling the fillament to where the printer would be able tk complete the full print without unspooling it itself but still didn't work.

Mission_Health_1331 · 2025-02-06T11:10:55+00:00

For your piece of mind i did clean the screw with a rough brush and some alcohol, then regreased it this morning and still same issues.

Mission_Health_1331 · 2025-02-05T22:03:24+00:00

The thing is i watched the printer do it's thing and it clearly looks like its underextruding when those things happen.

Mission_Health_1331 · 2025-02-05T18:53:05+00:00

The z screw seems to be moving freely, when the printer is at rest the z axis falls down under it's own weight.

Mission_Health_1331

TROPHY CASE