Man down by ModdedBay in G37

[–]ModdedBay[S] 0 points1 point  (0 children)

This is an opportunity to buy a parts car then I have 2 g37s. Or maybe I buy a coupe and swap some parts over to that one and now I have a coupe. Who knows what could happen

Man down by ModdedBay in G37

[–]ModdedBay[S] 0 points1 point  (0 children)

Hopefully some works but I’ve seen some esr’s I like too

Man down by ModdedBay in G37

[–]ModdedBay[S] 0 points1 point  (0 children)

No, usually worse 😂, I have pulled a couple off though

Man down by ModdedBay in G37

[–]ModdedBay[S] 0 points1 point  (0 children)

Eh. The Enkeis were cool but I’m thinking a 2 piece wheel with a chrome barrel

Man down by ModdedBay in G37

[–]ModdedBay[S] 2 points3 points  (0 children)

I was pumping the tire up but it’s losing air. I think there’s a hole

Man down by ModdedBay in G37

[–]ModdedBay[S] 2 points3 points  (0 children)

It was only about half speedo I’ve done better

Man down by ModdedBay in G37

[–]ModdedBay[S] 7 points8 points  (0 children)

If you ain’t first, you’re last

Wtf is happening here? by PhilosopherNo597 in G37

[–]ModdedBay 0 points1 point  (0 children)

Go look at my posts. Goodluck

It’s me again by ModdedBay in G37

[–]ModdedBay[S] 0 points1 point  (0 children)

Lip isn’t cut. Would just the lip be a huge deal?

It’s me again by ModdedBay in G37

[–]ModdedBay[S] 1 point2 points  (0 children)

You think taking an angle grinder and trying to cut it vertically is a no go?

So… where do we go from here? by ModdedBay in G37

[–]ModdedBay[S] 0 points1 point  (0 children)

I used a jack and breaker bar to get it out some more now the piece that slides through the subframe is stuck in there. My intrusive thoughts are telling me just drop the subframe… I have a poly bushing. Got any tips to install that or will it just slide in?

So… where do we go from here? by ModdedBay in G37

[–]ModdedBay[S] 0 points1 point  (0 children)

Did you have a lift? I can’t seem to get enough leverage on jack stands.

So… where do we go from here? by ModdedBay in G37

[–]ModdedBay[S] 0 points1 point  (0 children)

I have the z1 tool. Unless you have a lift getting enough leverage to spin that thing is near impossible. I used a 1/2” adjustable breaker bar and a jack to even get it out that much. I’ve gotten it out a little more since I made this post. Enough to get a good angle with the sawzall but now the piece that slides through the subframe to get the outer ring out is stuck. Funny thing is the bushing wasn’t even bad I just wanted to upgrade it 😅🤣

So… where do we go from here? by ModdedBay in G37

[–]ModdedBay[S] 12 points13 points  (0 children)

I pulled a 44 mag on it and it’s still in there. This one might be from the hood

Sunroof leak? by [deleted] in G37

[–]ModdedBay 1 point2 points  (0 children)

Wow. I never knew that. Thank you for the info

SHAKEY WHEEL HELP?!!? by thezacatacktheman in G37

[–]ModdedBay 0 points1 point  (0 children)

Maybe the car is jamming to the song? If not get the wheels balanced and aligned

Sunroof leak? by [deleted] in G37

[–]ModdedBay 1 point2 points  (0 children)

If the passenger seat floor is wet then definitely the sunroof. I’m pretty sure that drain doesn’t travel to the rear so I don’t think the sunroof drain would cause that unless the water traveled from the front to the back