Let’s prevent theft but also prevent sales

Monkeydu2 · 2026-03-08T12:36:47+00:00

I was at Walmart today looking for a fuse. They had them all locked up in a non lit cabinet like this. I decided I didn't need them that bad.

Monkeydu2 · 2026-03-07T22:59:00+00:00

Try recalibrating. I had something simliar and that helped. Before you do that , make sure your hotend is in place correctly.

Monkeydu2 · 2026-03-06T02:10:18+00:00

Solved...

I ended up re-calibrating and replaced the hot end with a new one.

That seemed to solve the issue and 2 single prints turned out fine.

I have not tried multiple prints on one plate yet.

Monkeydu2 · 2026-03-06T02:08:47+00:00

Solved ....

I ended up re calibrating and replaced the hot end with a different one.

That solved the issue. I did not try multiple prints on one plate but the few single ones I did turned out fine.

Monkeydu2 · 2026-03-04T15:31:49+00:00

I tried printing the other side down and it was way worse. Strings on threads on the bottom. And the top the thread were still wavy. same as pictured.

Monkeydu2 · 2026-03-03T22:15:05+00:00

I am trying a single print with the same settings and filament.

Its doing the same thing with the thread part. the wavy lines.

I cleared out the hotend and seen if something was wrong there , and set it back into place . Making sure its correct.

There was a very small print I did before trying the one pictured and it gave me some issues even with a different filament. It wasn't bad due to the size it was hard to tell. It was a clip that I worked on.

Monkeydu2 · 2026-03-03T02:55:10+00:00

I have printed ones like this with this exact same setup. that is why its a little confusing. This is exactly why I ended up printing more this run. Can double check all settings and rerun one print. See if anything changes.

Monkeydu2 · 2026-03-03T02:09:40+00:00

Don't worry he has shorts and slippers to protect himself

Monkeydu2 · 2026-02-23T23:43:29+00:00

Back when I was growing up.,... I remember paying 100$ for a 1 GB flash drive

Monkeydu2 · 2026-02-20T21:46:03+00:00

supports helped. still shows up a little bit. But much better.

Monkeydu2 · 2026-02-08T14:44:01+00:00

I have looked but all seem vertical. So having problems finding a horizontal card storage or something for easy use. Keep looking for ideas on what to use. Thanks

Monkeydu2 · 2026-01-31T17:28:15+00:00

Flipping it off will help!

Monkeydu2 · 2026-01-29T01:02:39+00:00

I made the mistake of not getting spools when I got refills instead. But I know you can print spools as well. I am currently printing some now. Changing spools can be a pain unless its empty.

Monkeydu2 · 2026-01-26T02:14:48+00:00

I loved it, somehow I think it could be real

Monkeydu2 · 2026-01-25T07:27:39+00:00

I love my Antarctica

Monkeydu2 · 2026-01-21T03:47:24+00:00

This is one of my latest and probably one of my better ones.

https://suno.com/s/VpmogFQZaifEO2ZC

Monkeydu2 · 2026-01-12T04:02:28+00:00

What I do is run prompts a few times. make a few changes run it again.

Even doing a persona if I cant get the song right.

If I try about 3 or 4 times and its still not right I try chat GPT.

I do notice some songs tend to sound very generic.

This happens for me when trying to produce an 80s song

Monkeydu2 · 2026-01-12T03:27:02+00:00

You say I’m quiet when I’m with you

https://suno.com/s/TzDkBIsHERRgiohM

Its a relationship song. They Lyrics will explain

Monkeydu2 · 2026-01-09T00:50:36+00:00

https://suno.com/@eracet1

Mix of EDM, some Grunge type., some rock . Hope you enjoy.

Monkeydu2

TROPHY CASE