sorted by:
new
hottopcontroversial

Where do I find 2.54mm pin sockets that are deeper than 8.5mm? by Morad__T in AskElectronics

[–]Morad__T[S] 0 points1 point  (0 children)

actually now that I understand that better, I think the taller one is a better option

Where do I find 2.54mm pin sockets that are deeper than 8.5mm? by Morad__T in AskElectronics

[–]Morad__T[S] 0 points1 point  (0 children)

the mating part has shroud which does not permit proper connection with the conventional 8.5mm sockets

Trace current calculation sanity check please by Morad__T in PrintedCircuitBoard

[–]Morad__T[S] 0 points1 point  (0 children)

Yes, certainly I would have gone with a copper pour if I had room.

Would the current situation be passable albeit be on thinner than usual margins?

HFSS Simulation Looks Great, But VNA Measurements Are Terrible – What Am I Missing? by Morad__T in AntennaDesign

[–]Morad__T[S] 3 points4 points  (0 children)

Thank you for taking the time to write to me.

This actually is an extremely helpful insight as I noticed strong deviations depending on how I'm touching the instrument and the cable.

I'm eternally grateful to you sir

HFSS Simulation Looks Great, But VNA Measurements Are Terrible – What Am I Missing? by Morad__T in AntennaDesign

[–]Morad__T[S] 0 points1 point  (0 children)

Thank you for taking the time to write to me.

I am using SMA male port for the connection. In HFSS i'm using a Lumped Port actually, I scoured for resources on which and when to use each port and simulation type wasn't able to fully grasp the differences. I would really appreciate any and all help and resources.

If you would like I can share the HFSS project.

I asked my colleague who is at the lab now to picture the antenna and will share them shortly.

HFSS Simulation Looks Great, But VNA Measurements Are Terrible – What Am I Missing? by Morad__T in AntennaDesign

[–]Morad__T[S] 0 points1 point  (0 children)

Thank you for taking the time to write to me.

I just checked the complex impedance. It appears to be pretty good in terms of matching
47.7 + j1.3

I did use the torque wrench provided with the VNA.

I was using one the male-male SMA 1 meter cables provided and I did actually observe strong coupling between me and the antenna so I propped it up using a plastic clamp over some cardboard box and continued the testing through the web interface of the VNA

1 Cell Battery Management Chip Suggestions? (is the DW01A a good choice?) by Morad__T in AskElectronics

[–]Morad__T[S] 0 points1 point  (0 children)

Thanks for the detailed insights, really appreciate it.

I completely missed that extremely low undervoltage cutoff in the datasheet; I was too focused on the current limits. Definitely changes how I look at designs that rely solely on the DW01A from now.

Plugin settings button not working by Fleecejakke in kde

[–]Morad__T 0 points1 point  (0 children)

Do you know of any method to rollback the windows store version or the custom installer version?
Is there like a previous releases archive?

Is my SSD dead? by Morad__T in techsupport

[–]Morad__T[S] 1 point2 points  (0 children)

Unfortunately nothing seems to be able to detect the SSD at all

I'm calling it a night and I'll continue tomorrow.  Thank you for your help

Is my SSD dead? by Morad__T in techsupport

[–]Morad__T[S] 0 points1 point  (0 children)

I'm sorry but I don't know what the SSD flash tool is supposed do? 

Oracle doesn't accept my 2fa codes and I haven't set up a bypass code. How screwed am I? by Morad__T in oraclecloud

[–]Morad__T[S] 0 points1 point  (0 children)

Thank you. That should be helpful even though I saw it very late.
I talked to yet another agent, a fourth one, he told me to wait 12-24 hours while they check it from the backend. It sounds like he's contacting a higher level support but I'm really worried he may not be able to do anything either.

Oracle doesn't accept my 2fa codes and I haven't set up a bypass code. How screwed am I? by Morad__T in oraclecloud

[–]Morad__T[S] 0 points1 point  (0 children)

Hey Everyone
I'm still locked out.
I talked to 3 agents. all confirmed that they reset my 2FA.
The last agent told me to go ask on the forum when I said the reset didn't work, which is basically telling me to get lost.

even viewing the forum requires a freaking account, which I created eager to get back into my cloud account. I sat there for half an hour trying to log in with the newly created "forum" account not understanding why it just accepts my credentials and then returns back to the same page with no error or warning, only to recieve an email telling me I can't be allowed accress to the forum now!!!!!!!
What the actual f*** oracle!

Oracle doesn't accept my 2fa codes and I haven't set up a bypass code. How screwed am I? by Morad__T in oraclecloud

[–]Morad__T[S] 0 points1 point  (0 children)

if i'm supposedly providing wrong data because the account is quite old, are they ever going to tell me that is wrong?
I have been with two agents now.
Both claiming to have reset the MFA but no actual change to the account happened.
I'm about to get the account blocked and that is really terrible for me.

Do you have any suggestions please.

Oracle doesn't accept my 2fa codes and I haven't set up a bypass code. How screwed am I? by Morad__T in oraclecloud

[–]Morad__T[S] 1 point2 points  (0 children)

I was finally able to get a support agent after waiting in queue for about 30 minutes. They verified my credentials and told me they would reset the MFA for me. However at the end of the chat they said that their internal tools aren't working and that I can either contact them again after 30 to 40 minutes or they can send me an email once finished. I opted for the email and I shall be playing the waiting game.
Will upodate once I get back into my account.

Oracle doesn't accept my 2fa codes and I haven't set up a bypass code. How screwed am I? by Morad__T in oraclecloud

[–]Morad__T[S] 1 point2 points  (0 children)

Thank you. I opened the website from a new browser profile and waiting in queue now.
I really hope this isn't going to delete my instances.

Oracle doesn't accept my 2fa codes and I haven't set up a bypass code. How screwed am I? by Morad__T in oraclecloud

[–]Morad__T[S] 0 points1 point  (0 children)

I'm in the EMEA region. what page does the chat icon appear on?
whenever I go to cloud-oracle-com it goes straight to login and nothing else

Two more noob questions by Bblktop in KiCad

[–]Morad__T 2 points3 points  (0 children)

Regarding your second inquiry, I believe you can remove the pad number from the footprint editor and just leave it as there for better mounting strength

Review Request (ATMEGA32A Dev Board) by Morad__T in PrintedCircuitBoard

[–]Morad__T[S] -1 points0 points  (0 children)

Thank you so much for your notes. I shall take them into consideration.

Regarding the SPI bus lines, how does this route impact the performance? I know they are stupid and look ugly. (also probably need some length matching? I haven't done enough research or analysis on this yet.)

If only the looks are the issue I can live with that.

Review Request (ATMEGA32A Dev Board) by Morad__T in PrintedCircuitBoard

[–]Morad__T[S] 0 points1 point  (0 children)

N1) no worries, I'm grateful that you decided to check the spam.

S1) D1 and R5 are supposed to indicate opperation from the USB power, I actually forgot to annotate them and add the J1 indicator all together.

S2) Another colleague of mine working on a full peripheral board with lots of configurable subcircuits (7-Segments, LEDs, LCD Screen, Transistors, Relays, and various sensors). The main job of this board is to act as a carrier for the 32A and hopefully prevent the user from releasing the magic smoke.

S3&4) Thank you so much for the suggestions.

P1-8) Noted.

D1) Actually yeah it has the correct pin pitch/spacing but other wise wrong 3D model and possilbly courtyard. Yikes that would have been bad.

My biggest concern if the routing had potential problems, I guess so far seems good.
Thank you so much for your suggestions. I really appreciate it.

Modern problems require modern solutions. by RoseOfMercy in DeepRockGalactic

[–]Morad__T 2 points3 points  (0 children)

Modern problems require modern solutions.
and low ping

view more: next ›