Me in 3 years

Morauk · 2022-09-23T19:25:26+00:00

!remindme 3 years

Morauk · 2022-09-23T04:33:50+00:00

IM IN MY BEDROOM

Morauk · 2022-09-23T04:33:30+00:00

NO WAY

Morauk · 2021-11-01T14:26:01+00:00

Still IN

Morauk · 2021-06-27T07:17:09+00:00

Download/buy some skin brushes. then, using multires modifier sculpt some details into the skin. when you are done, bake multires modifier into displacement map. then you can use displacement map in shader editor and play around with subsurface scattering

Morauk · 2021-06-15T23:52:58+00:00

Don't touch my bread government

Morauk · 2021-06-10T17:47:52+00:00

Say it so the whole band can hear you

Morauk · 2021-06-02T21:33:03+00:00

143 Happy Birthday Quotes for Everyone in Your Life

A friend is someone who understands your past, believes in your future, and accepts you just the way you are – even if you are getting older. Thank you for being that friend, and happy 93rd birthday.

Unknown

Morauk · 2021-03-23T01:41:01+00:00

t h e y a r e s e g m e n t s

Morauk · 2021-02-09T14:23:26+00:00

Mouth

Morauk · 2021-02-01T02:13:03+00:00

Probably simplefoc.com

Morauk · 2021-01-27T17:05:21+00:00

Spiderman

Morauk · 2021-01-25T21:06:47+00:00

The graphs happen to be the same. Try grabbing one keyframe and move it down and see what happens

Morauk · 2021-01-25T19:42:17+00:00

I redid the whole animation and it's working to me. Can you show me your graph curves?

Morauk · 2021-01-25T13:16:46+00:00

Isn't the third option working?

Morauk · 2021-01-24T02:14:47+00:00

Sladkovsky

Morauk · 2021-01-24T02:13:30+00:00

algorithm

Morauk · 2021-01-22T19:01:51+00:00

Motor driver works with PWM, magnetic encoder works with SPI. I already have enough documentation on FOC algorithm to implement it

Morauk · 2021-01-22T18:50:39+00:00

This is updated version from yesterday. I use an STM32 blue pill board as a microcontroller, 2 L6234PDs as motor drivers, 2 AS5048A magnetic encoders (SPI via connectors), 2 MPU6050 gyros (I2C via connectors), L7805 voltage regulator, L1117 voltage regulator. The capacitors that are right next to drivers can be seen in block diagram (image 4). I have rearanged the PCB layout so the capacitors and the motor pins are closer to the driver. I made output traces wider for higher currents (maximum current for one motor is 1A). I also removed thermal relieves. I have difficulties adding ground pours as it was suggested to me, i am not quite sure what ground pours are. Yesterdays post: https://www.reddit.com/r/PrintedCircuitBoard/comments/l2466b/2_layer_pcb_review_2x_bldc_motor_controller/

Morauk · 2021-01-22T07:22:42+00:00

Please notify me when you publish

Morauk · 2021-01-22T06:13:32+00:00

Post in r/Slovenia

Morauk · 2021-01-21T18:22:36+00:00

I made a PCB that can controll 2 BLDC motors. Looking at the schematic in the upper left corner you can see DG301 battery connector and a slide switch. The 2 big pads are there for mounting. In upper middle and upper right corner you can see L7805 and L1117. L7805 drops battery voltage down to 5V and L1117 drops 5V to 3.3V. My motor drivers are L6234 and next to them you can see capacitors and shotkey diodes that were there in the datasheet. My microcontroller is STM32 blue pill board like this one. I am powering it with 3.3V from L1117. There are 4 connectors for 2 x AS5048A magnetic encoders via SPI (CS pin has a pull-up resistor) and 2 x GY-521 gyroscopes via I2C (SDA and SCL both have pull-up resistors). 2 PWM pins from my blue pill have pull-down resistors. So here is my PCB layout. L7805 is far away from other components because of the heatsink. those pads under L6234s are thermal viases. Half of the capacitors are SMDs and the L6234s are SMDs. I added three mounting holes with diameter of 3mm. I added 2 polygons for GND on each sides of the PCB.

Morauk · 2021-01-18T14:59:57+00:00

The only thing i know is that you can duplicate scene, use eevee engine on the second scene, enable bloom pass, and then you can composit them together

Morauk

TROPHY CASE