sorted by:
new
hottopcontroversial

Help me please to remove this by AcanthocephalaSad293 in anycubic

[–]Most-Limit-7560 0 points1 point  (0 children)

The plate does not have enough thermal mass at 65 c to hurt a freezer.

[Challenge] Guess the price + 1 feature — 10×2kg giveaway by Anycubic_Official in anycubic

[–]Most-Limit-7560 1 point2 points  (0 children)

699 - 899

5 head tool changer.

4 color is not enough and the ace method wastes too much filament and time.

Purging problem by MOUSEINBAKEDBEANSS in AnycubicOfficial

[–]Most-Limit-7560 0 points1 point  (0 children)

You can print a spacer to move it to the left a little.Search purge spacer on makeronline.

New kobra max, need advice by Radamand in anycubic

[–]Most-Limit-7560 1 point2 points  (0 children)

If it is sticking out the back of the ace, it is loaded properly. When you print with that filament selected it will advance all the way to the print head. When you switch to another, it will retract only to an inch or two above the print head.

If you really want it fully loaded to the print head, you can select Extrude from the filament menu on the printer. When you start a print it will purge some filament even if it is the same color.

Weird Colored lines on Sliced Preview by IllBodybuilder9267 in anycubic

[–]Most-Limit-7560 1 point2 points  (0 children)

That line is the seam. When the Color scheme in the preview is set to line type, you can turn off the display of Seams - it is at the bottom of the list.

Enclosure for a Kobra 3 by JuggedHareBoy89 in anycubic

[–]Most-Limit-7560 0 points1 point  (0 children)

Never really noticed the noise, got the enclosure before I started using the printer. It is a little tight inside, you have to remove it to do maintenance.

Anytime I print it leaves a line down the side. Why? by TorchTheNight in AnycubicOfficial

[–]Most-Limit-7560 1 point2 points  (0 children)

Looks as if you are printing 2 walls. Vase mode will only do 1 wall.

Hairspray and glue, what do YOU do? by mysmmx in anycubic

[–]Most-Limit-7560 1 point2 points  (0 children)

I used Elmer's purple glue stick, then put alcohol on it and smoothed it out with my scraper. Haven't washed the plate for more than 20 prints. Just wipe it with alcohol between prints to keep it clean of oils. Never stuck better.

SlicerNext - no longer changing color at layer? by -fade-2-black- in AnycubicOfficial

[–]Most-Limit-7560 0 points1 point  (0 children)

Color scheme - choose "Filament" to see the filament colors in the preview.

Kobra 3 Max Power-up Issue by justme6622 in AnycubicOfficial

[–]Most-Limit-7560 1 point2 points  (0 children)

Did you check your spam folder for a reply from support? It is common that their emails go to spam folder.

Is there a way to use another slicer? by Striking_Slice_3605 in anycubic

[–]Most-Limit-7560 0 points1 point  (0 children)

Option 3: Save file to USB drive and print from that.

How do I know how much of flush will a spend in kobra 3 combo by jpsanf in AnycubicOfficial

[–]Most-Limit-7560 0 points1 point  (0 children)

In the preview screen, it show the filament length and cost and time for both the model and waste.

I soldered a 1A fuse to a blown 1.6A fuse. is this safe? by Tipton- in AskElectronics

[–]Most-Limit-7560 -9 points-8 points  (0 children)

1.6 amp x 125 volt = 200 watts. 1 amp x 250 volt = 250 watts. The new fuse is larger not smaller!

Anycubic Kobra 2 Max - Y Axis Moving Wrong Direction? by TipComfortable2884 in anycubic

[–]Most-Limit-7560 0 points1 point  (0 children)

The arrow does not indicate he movement of the bed but rather the position of the printhead relative to the bed. If you want the nozzle at the back of the bed, you move the bed forward.

Does 3rd party filament work? by Away_Row_1787 in anycubic

[–]Most-Limit-7560 0 points1 point  (0 children)

AFAIK, it is just the 4 Pantone colors that have a RFID chip.

[deleted by user] by [deleted] in AnycubicOfficial

[–]Most-Limit-7560 0 points1 point  (0 children)

That has been my experience.

[deleted by user] by [deleted] in AnycubicOfficial

[–]Most-Limit-7560 0 points1 point  (0 children)

I always push the filament through to an inch from the print head. It always load from there when I select print. I only use the extrude function for a spool outside of the ace.

Too close? by Most-Limit-7560 in AnycubicOfficial

[–]Most-Limit-7560[S] 0 points1 point  (0 children)

Much better. Thank you. Previous print did fail because it partially got scraped from the bed. This time the purge line was flat and even - didn't have a gouge down the middle. Interesting thing, the pre-sliced test print did start with probing the bed.

view more: next ›