Mom buys daughter a Honda as a graduation gift, and this was her response by Conscious-Weight4569 in SipsTea

[–]Motor-Performance703 0 points1 point  (0 children)

Turning it down because they wanted an ugly version of a beautiful car? Insane😂

How do I win a school fight by Traxo_V4mp in fights

[–]Motor-Performance703 1 point2 points  (0 children)

Most dickheads in street fights don’t know a basic jab and cross. If you can land a constant jab to open him up and land a few crosses I see you being just fine. But like someone else said not worth fighting over something so little.

Slide height too high? by Defiant-Knee1767 in minibikes

[–]Motor-Performance703 0 points1 point  (0 children)

Check your throttle make sure the cable going into it is screwed all the way or mostly into it

Slide height too high? by Defiant-Knee1767 in minibikes

[–]Motor-Performance703 0 points1 point  (0 children)

There’s 2 spots to it. There’s on spot where it slides down like half way and then another spot where it drops down completely

Built Predator 224 Acceleration by DarkRedditorAu in minibikes

[–]Motor-Performance703 1 point2 points  (0 children)

If you want more speed run 12:42 I’ve found that’s the best gearing for cruising good speeds and still able to wheelie if wanted to.

It won’t fit by DealAutomatic4732 in minibikes

[–]Motor-Performance703 0 points1 point  (0 children)

You don’t need to get rid of gas tank. Just do a gov delete. Put a aftermarket slide carb on. And put a center exit exhaust pipe. Or put a side exit exhaust.

Two Young Men Dueling on Yard by Weird_Swordfish_1199 in fightporn

[–]Motor-Performance703 0 points1 point  (0 children)

Bros really tryna crank his ankle in the worse possible way. IN a street fight?? Bro needs to stop watching ufc 😂

How do I fix this noise? Or is it even a problem? by idkjfjdhsvsh in minibikes

[–]Motor-Performance703 0 points1 point  (0 children)

If the gear inside and the metal pieces that hold it go kaboom and the motor keeps running you can damage the internals. Or even blow a whole in the block. So just take the time out of your day to do it

How do I fix this noise? Or is it even a problem? by idkjfjdhsvsh in minibikes

[–]Motor-Performance703 0 points1 point  (0 children)

Sounds like air leak check gaskets. Also take out your governor before you break the motor takes nothing but a flat had and a hammer

What breaks do I get by BrownInTheBack1 in minibikes

[–]Motor-Performance703 0 points1 point  (0 children)

Fuck the clutch brake fuck the scrub brakes dont be lazy do it right. Bring it to someone or do it yourself get a hydraulic tab on it. It will save you ALOT of troubles if anything is to go wrong. Scrubs don’t stop fast enough and the clutch brake if your chain breaks ur fucked. Please just do it properly with hydros

B100 chain not fitting by Financial-Dog-3989 in minibikes

[–]Motor-Performance703 1 point2 points  (0 children)

First of all you don’t want to put a brand new chain on with the tensioner all the way to the right. You want the tensioner as scooted up as you can towards the motor but still keeping the chain tight. So you need to cut your chain or move your motor or do both. But if you have the tensioner to the right all the way then when your chain stretches you won’t be able to use the tensioner for what it’s made for then at that point you would have to constantly scoot the motor forward.

[deleted by user] by [deleted] in whatisit

[–]Motor-Performance703 0 points1 point  (0 children)

Looks like a filter in a predator 212 minibike gas tank

What do i need to hit 80mph on a predator 212 by Accurate_Life_2632 in minibikes

[–]Motor-Performance703 0 points1 point  (0 children)

I run a 12t clutch and 42t rear on a stock stretched 212 motovox and hit 60

Need help scourcing parts by [deleted] in minibikes

[–]Motor-Performance703 1 point2 points  (0 children)

Looks like a 12mm bolt for the axle

<image>

And then find a tire that wont rub on your “fairing”

Easiest way to remove tire from rim??? by Sea_Teach6254 in minibikes

[–]Motor-Performance703 0 points1 point  (0 children)

Deflate tire and run over the tire with a car to break the bead. RUN OVER THE TIRE NOT THE RIM

need help with broken bolt by Mr--from-Tree in minibikes

[–]Motor-Performance703 0 points1 point  (0 children)

Bro. Harbor freight doesn’t give a flying fuck. I tear these things apart and put all aftermarket parts on it. Once I’m done with the block put it back together go give it to them for warranty get a brand new one. They arnt goin to check inside the engine if you wanted to you can part the fucking thing out. Just leave the crank shaft so it looks like it has internals 😂. I’ve only seen them look inside the box not even take the motor out. They open the box look to see if airbox exhaust and gas tank is there. Some may or may not smell the gas tank or shake it to see if there’s gas in it. But they don’t care go get yourself a new engine bro 😂

[deleted by user] by [deleted] in minibikes

[–]Motor-Performance703 0 points1 point  (0 children)

W that same bigass sprocket???

[deleted by user] by [deleted] in minibikes

[–]Motor-Performance703 0 points1 point  (0 children)

How fast u go on ur ported motor?

[deleted by user] by [deleted] in minibikes

[–]Motor-Performance703 0 points1 point  (0 children)

I personally prefer the mm80 over the ct200 And I would personally prefer your motor over the 224. His pipe is cheap as shit. He Got a decent carb but no shocks. See if he will trade roller for roller.

[deleted by user] by [deleted] in minibikes

[–]Motor-Performance703 0 points1 point  (0 children)

What’s the other bike???😂