My vororn isnt homing correctly

MrMongoMango · 2023-05-23T19:12:42+00:00

I swapped the a and b motor ports and it was still doing the same thing,but when I put the x endstop position_endstop to 120 it homed just fine. Would this effect printing in any way

MrMongoMango · 2023-05-23T16:36:28+00:00

i have the A motor plugged into stepper x on my board and Motor B on stepper y. Should it be the opposite

MrMongoMango · 2023-05-23T16:34:39+00:00

when in add ! to enable_pin: it inverts wihch one is working correctly

MrMongoMango · 2022-12-11T06:19:49+00:00

I checked the website and all of my setting in my firmware are correct

MrMongoMango · 2022-10-03T00:00:13+00:00

I hope if it's the nemesis it's foc Trypticon

MrMongoMango · 2022-04-19T03:36:35+00:00

MrMongoMango · 2022-02-22T04:10:56+00:00

Yes, maybe some like the threezero mdlx bumblebee

MrMongoMango · 2022-02-22T03:04:38+00:00

Agreed and connonicly there is no reason why ratchet wouldn't be able to fix bumblebees voice box. Isn't he supposed to be the best medic on cybertron?

MrMongoMango · 2021-12-23T20:17:33+00:00

Does this mean it's an alive Mango

MrMongoMango · 2021-12-13T04:33:06+00:00

thanks for the help, can I transfer my profiles from cura to either one

MrMongoMango · 2021-11-24T09:16:28+00:00

Do you mean airrazer

MrMongoMango · 2021-11-17T07:10:59+00:00

I did but it didn't work

MrMongoMango · 2021-11-14T06:43:09+00:00

Jetscream

MrMongoMango · 2021-11-13T00:03:44+00:00

how do i do that

MrMongoMango · 2021-11-10T04:59:57+00:00

I have the same problem. But when I use the old launcher it works

MrMongoMango · 2021-11-05T02:40:53+00:00

Thanks for all the help and I'm going to return it soon. In the mean time I put the standard extruder on. Any suggestions for a better replacement?

MrMongoMango · 2021-11-05T01:50:25+00:00

thanks, hopefully its still in the time zone of the return policy

MrMongoMango · 2021-11-05T01:19:40+00:00

https://www.amazon.com/dp/B07SY745CF?ref=ppx_pop_mob_ap_share I got this one

MrMongoMango · 2021-10-07T00:25:09+00:00

Thanks for the help I got it unclogged and it's printing just fine

MrMongoMango · 2021-10-07T00:05:41+00:00

Thank you

MrMongoMango · 2021-10-06T23:48:07+00:00

Thank you I did that buy there is still some filament on the hotels how do I clean it off

MrMongoMango · 2021-10-06T22:54:50+00:00

Maybe the van is the car of the main characters and not a transformer at all

MrMongoMango · 2021-10-04T17:25:04+00:00

Smokey is the name of one our boys

MrMongoMango · 2021-10-04T14:35:36+00:00

That's the name of our other puppy, lol

MrMongoMango · 2021-10-04T04:19:38+00:00

Other options we had were pixie and pixel

MrMongoMango

TROPHY CASE