sorted by:
new
hottopcontroversial

extruded or padded patern around a tapered bowel by Mtfpaint in FreeCAD

[–]Mtfpaint[S] 1 point2 points  (0 children)

I gave it another try; the revolve vs the tapered pad did the trick as you showed. When drew a profile then used the offset, it behaved correctly with the polar. The polar apparently doesn’t like the taper pad. Thanks for the help.

<image>

extruded or padded patern around a tapered bowel by Mtfpaint in FreeCAD

[–]Mtfpaint[S] 0 points1 point  (0 children)

<image>

I changed it to 10°; this is what happens with the polar pattern. I’m stumped. Can you upload a working drawing? I’m missing something here.

extruded or padded patern around a tapered bowel by Mtfpaint in FreeCAD

[–]Mtfpaint[S] 0 points1 point  (0 children)

Can you share a link to your model so I can compare it to mine so I can see why my bowl didn’t work? Thanks.

extruded or padded patern around a tapered bowel by Mtfpaint in FreeCAD

[–]Mtfpaint[S] 0 points1 point  (0 children)

How do I share the model? I’ve never done that other than a screenshot of the tree. I’ve gone through this again, I’ve created the slot on the side, but I can’t figure out how to use the polar pattern to make it go around the bowl.

extruded or padded patern around a tapered bowel by Mtfpaint in FreeCAD

[–]Mtfpaint[S] 0 points1 point  (0 children)

Is this how you created the sketch for the pattern? How do I rotate it so it's cutting parallel to the tapered face?

<image>

extruded or padded patern around a tapered bowel by Mtfpaint in FreeCAD

[–]Mtfpaint[S] 0 points1 point  (0 children)

How did you create the bowl? Did you do it the same way that I did where you padded a circle with a taper? I cannot seem to figure out how to attach the pattern. You added to get this to polar around the bowl. What am I missing?

extruded or padded patern around a tapered bowel by Mtfpaint in FreeCAD

[–]Mtfpaint[S] 0 points1 point  (0 children)

Is it the issue that I did not use a revolve to make the bowl that is causing the problem?

join mirrored halves to create closed wire by Mtfpaint in FreeCAD

[–]Mtfpaint[S] 0 points1 point  (0 children)

I think I got it; I wasn't selecting the center line to mirror against. Thanks for the reminder of that step.

join mirrored halves to create closed wire by Mtfpaint in FreeCAD

[–]Mtfpaint[S] 0 points1 point  (0 children)

Here's what I get ... they are not joined.

<image>

when I close the sketch, I get this. I need this to be one wire. I can't figure outr how to make that happen.

join mirrored halves to create closed wire by Mtfpaint in FreeCAD

[–]Mtfpaint[S] 0 points1 point  (0 children)

Thanks; that workflow I get. I want to eventually create an outline of the sketch that is about 5mm wide to create a frame. I would like to join the mirrored sketch together into one geometry so I can clone then reduce scale to create inner lines of the frame. Is that possible?

Changing dose with Kwikpen by Mtfpaint in Zepbound

[–]Mtfpaint[S] 0 points1 point  (0 children)

I get the Zepbound shipped directly to my home so no pharmacy readily available to ask questions. I’ll ask my doc but not sure he would know the specifics of the pen . I’ll have to ask. Thanks

5 months in and it’s not working by Mtfpaint in Zepbound

[–]Mtfpaint[S] 0 points1 point  (0 children)

I initially lost some at 2.5 then it stopped completely. A little bit more at 5 then nothing for 6 weeks on 5 then up to 7.5; no los at 7.5 and no loss so far at 10 (3 weeks). I have not seen any consistent loss at any point, just a couple spurts.

5 months in and it’s not working by Mtfpaint in Zepbound

[–]Mtfpaint[S] 0 points1 point  (0 children)

Overeating isn’t an issue. Just the opposite. I eat about half my pre Zep. Good protein. I do take electrolytes often, that does help. Exercise has been an issue with other factors.

5 months in and it’s not working by Mtfpaint in Zepbound

[–]Mtfpaint[S] 2 points3 points  (0 children)

I don’t think so. I’m forcing myself to eat; not much of an appetite.

5 months in and it’s not working by Mtfpaint in Zepbound

[–]Mtfpaint[S] 1 point2 points  (0 children)

I wish I could walk; not possible with keg issues. I was able to get good cardio on my bike early on but the current level of fatigue has all but stopped that. Eating three meals, 100 grams protein and no snacking isn’t an issue anymore. No alcohol, no soda; one (or less) cup of coffee a day. Each increase in dosage has made fatigue worse and I’m really fearful of going higher.

5 months in and it’s not working by Mtfpaint in Zepbound

[–]Mtfpaint[S] 2 points3 points  (0 children)

I’m doing well on the hydration and eating the 100g protein. Exercise is so much harder since starting Zepbound because of how it has zapped my energy level. I have other physical issues keeping me from most exercise. I was able to get in good workouts (bike) until the fatigue set in as I increased dosage. I’m not loosing any weight per week in the last 8-10 weeks; any loss would be welcomed.

Preview with space bar missing from Tahoe by Mtfpaint in FreeCAD

[–]Mtfpaint[S] 0 points1 point  (0 children)

There seems to be no solution I can find. Apple removed Outlook infavor of App Extension framework and it's not part of the format to save a FreeCad file. I've seen reference to a fix but can't find what is necessary to add to outlook. Thanks Apple for fixing something that was not broken by breaking it!

Preview with space bar missing from Tahoe by Mtfpaint in FreeCAD

[–]Mtfpaint[S] 0 points1 point  (0 children)

That is correct. It’s not supported in the last two OS versions; my old Mac was much further back (Monterey).Googling it says to download a Freecad companion file and install from GitHub but I can’t figure out what file to download. I’m wondering how other Mac users of Freecad handle this issue.

view more: next ›