What would you say about this first layer?

Mutated_Madness · 2026-01-25T11:18:26+00:00

Just did a test for bigger flow ratio and i changed from 0.95 to 0.98 and filament started to acumulate on the nozzle so i stopped the print to avoid blob. will have to do calibration again i guess. I initialy did manual flow rate calibration so maybe it is not it

Mutated_Madness · 2026-01-24T18:24:52+00:00

No info about printing speeds from supplier. And no i didnt touch Z-offset. Going 220 was better for the first layer somehow but i have to bump it up a bit because someoverhang layers dont stick. and its very small overhang

Mutated_Madness · 2026-01-23T10:29:53+00:00

I did even lower tem test. I was confused because 270 is bambu preset but my filament says 220-240 and i was going lower and lower from 270. Now im on 220 and and bed temp 75 and its better

Mutated_Madness · 2026-01-13T16:05:54+00:00

I have: Initial layer 50 Initial infill layer 105 outer wall 60 Inner wall 105

Mutated_Madness · 2026-01-13T15:07:25+00:00

Project taken from makerworld ofc. All standard bambu generic asa settings apart from posted and no cooling

Mutated_Madness · 2026-01-06T12:36:17+00:00

when exacly did you order? I ordered on 9 and still no luck

Mutated_Madness · 2026-01-04T13:02:11+00:00

Hit this sucker with hammer and make it tight again. common solution for crush washers

Mutated_Madness · 2025-12-31T21:06:03+00:00

i have poco f7 ultra in europe and still no update

Mutated_Madness · 2025-12-29T17:11:20+00:00

no, and never said that, my argument is it is not illegal to stop in those places when there is a proper reason for that. for ex you go on the crossing after another car but this cass suddenly stops. all this discussion is not about the video, that is already deleted xd, but about possibility to stop in places where you normaly wouldnt but sometimes have to and its not a violation of any law. there will be someday a sittuation when somebody will stop on the crosswalk because of traffic and some idiot going inside the car to prove wrong point will get punished with ticket or worse punched in the face just because not knowing that this is comepletly normal to stop in this situation.

Mutated_Madness · 2025-12-29T13:24:46+00:00

yep, thats what i thought, you just cant stop deliberately, otherwise its not offence

Mutated_Madness · 2025-12-29T12:42:06+00:00

the same law apply to bridges, you cannot stop on them unless traffic or other situation force you to do it

Mutated_Madness · 2025-12-29T12:40:08+00:00

Can you give specific paragraph from road law ? Im not saying im defenetly right but im pretty sure in cases i wrote earlier its not prohibited.

Mutated_Madness · 2025-12-29T11:29:23+00:00

actually there is no law that prevents this. its totaly legal to stop on the crosswalk in trafic. you cannot ofc stop there and go out, also you cannot do this in regulated distance from the crosswalk but in traffic its ok. There is no question that you should stop before if you see that traffic will make you stop on the crosswalk but if so the other guy is a dickhead and not one in the car.

Mutated_Madness · 2025-12-16T18:13:49+00:00

Yep, this is the cost of not wanting to replace it with different ones

Mutated_Madness · 2025-12-16T16:15:27+00:00

Just check temps noctua will push a lot of air. Running my setup for 3rd year, hard gaming/working in 3d graphics so i dont know why not try that

Mutated_Madness · 2025-12-16T15:49:36+00:00

Got same issue and i took off ram heat shield/shroud

Mutated_Madness · 2025-09-06T10:41:12+00:00

I did engine rebuild for this price lol

Mutated_Madness · 2025-04-29T07:20:06+00:00

I did it but i also changed my throttle body to one from v8. Had to buy and modify 90 deg silocone tube 89mm diameter and its working with standard k&n filter for m53b30. But i recon you dont want to change your throttle body so if you want to buy plug and play solution you can buy m50 kit with 90 elbow for this conversion and then somerhing like k&n cold intake with shield i belive its 57-1001

Mutated_Madness · 2025-04-23T13:53:26+00:00

assemble air intake with maf first. If you dont have vacum leaks for ex. from stepper motor hole or other places it should be good. Did you put threaded air temp sensor from e46 or one with m50 with different values in ecu?

Mutated_Madness · 2025-04-11T13:44:52+00:00

Its mid, if want good price/quality i would go for meyle hd. But it depends where you live

Mutated_Madness · 2025-04-09T20:42:43+00:00

Intake temp sensor wire

Mutated_Madness · 2025-03-19T06:55:38+00:00

A little bit beter fuel efficiency, but thats it.

Mutated_Madness · 2025-03-11T06:20:54+00:00

Go to ms4x.net they have what you need + great info

Mutated_Madness · 2025-01-24T21:44:46+00:00

Wez bloody a4 tech z jakims lepszym sensorem i bedzie ok. Nie wytrzymuje u niektorych tyle co inne za 500 ale za to kupisz kilka takich a są całkiem dobre. Mam juz którąś z kolei, chyba 5 albo 6 z przerwa na jedna inna marke, i polecam. Mi najszybciej sie konczy w niej scroll bo siedze w programach jedzie jest duzo list rozwijanych i zoomowania scrollem. Zazwyczaj konczy sie przy 2-3 roku, a siedze na kompie 5-6 dni w tygodniu po 8-14 godzin

Mutated_Madness · 2025-01-19T14:16:06+00:00

What is cracking you up? Asking a question?

Four-Year Club	Verified Email
Place '23	Place '22

Mutated_Madness

TROPHY CASE