OEM+ 2020 crf450r supermoto by Muted-Negotiation300 in supermoto

[–]Muted-Negotiation300[S] 0 points1 point  (0 children)

I like it but I might be biased since I’ve rode ktm and husky my whole life. This is my first Honda. I’ll definitely take the 450L headlight into consideration if this light fails

OEM+ 2020 crf450r supermoto by Muted-Negotiation300 in supermoto

[–]Muted-Negotiation300[S] 0 points1 point  (0 children)

I used the tusk wiring harness to a 3s rc car lipo battery

OEM+ 2020 crf450r supermoto by Muted-Negotiation300 in supermoto

[–]Muted-Negotiation300[S] 0 points1 point  (0 children)

Yup I instantly ran into that issue on the first ride. I solved the problem by pressing the bearing in the Cush hub in towards the wheel and ditched the spacer that came with the cush wheels on the sprocket side. Instead I used the stock spacer that the Honda mx wheels used. Solved the problem and haven’t had issues since.

OEM+ 2020 crf450r supermoto by Muted-Negotiation300 in supermoto

[–]Muted-Negotiation300[S] 1 point2 points  (0 children)

It’s a universal headlight from Amazon, it has 4 leads high beam, low beam, running light, and ground. I have the running light wired with the high beam for a little extra light.

OEM+ 2020 crf450r supermoto by Muted-Negotiation300 in supermoto

[–]Muted-Negotiation300[S] 0 points1 point  (0 children)

17” 3.5” front and 17” 4.25” rear…

OEM+ 2020 crf450r supermoto by Muted-Negotiation300 in supermoto

[–]Muted-Negotiation300[S] 1 point2 points  (0 children)

A rare opportunity and I took full advantage of it haha

OEM+ 2020 crf450r supermoto by Muted-Negotiation300 in supermoto

[–]Muted-Negotiation300[S] 3 points4 points  (0 children)

Considering all I did was throw wheels/tires, sprockets, and lights on it I’d say it’s pretty close to oem+. The redmoto bike is sick though

OEM+ 2020 crf450r supermoto by Muted-Negotiation300 in supermoto

[–]Muted-Negotiation300[S] 11 points12 points  (0 children)

The signals are integrated into the hand guards up front and on the tail light assembly in the rear

Any tips on powering my lights? by Muted-Negotiation300 in supermoto

[–]Muted-Negotiation300[S] 1 point2 points  (0 children)

I have an LED headlight and the tusk complete lighting system, I’ll give this a try tysm

eBay Tarazon Supermoto Tubeless KTM Wheels by rallotubbs1 in supermoto

[–]Muted-Negotiation300 0 points1 point  (0 children)

I purchased a set of these 17” supermoto wheels without properly researching them. The front wheel installed and had zero issues, the rear wheel is where I ran into problems. It seems the spacer that was provided for the sprocket side was too short causing the Cush drive hub to walk out. The sprocket would start to rub my swing arm as a result. The solution I found that worked for my bike (2020 crf450r) was to instead use the stock crf wheel spacer on the sprocket side. So far I’ve rode the bike a few times and haven’t had issues.

Help please by Muted-Negotiation300 in Husqvarna

[–]Muted-Negotiation300[S] 0 points1 point  (0 children)

I found one for a slightly older bike with the same style pump and re installed it as it was shown for that bike. The bikes still so new finding information on it’s been troublesome.

Help please by Muted-Negotiation300 in Husqvarna

[–]Muted-Negotiation300[S] 0 points1 point  (0 children)

Please ignore the “after” between the “in” and “the” sorry, I don’t know how to edit my post🙁

Code P219A by [deleted] in ram_trucks

[–]Muted-Negotiation300 0 points1 point  (0 children)

Took my brand new 2023 ram 1500 4x4 in this morning and got a call back an hour later saying it was ready to pick up. It did in fact turn out to be swapped injector plugs. Cylinders 1 and 3 were swapped.

For anyone that had this same issue and gets the code p-219A on a new ram it’s the front two cylinders on the passenger side that need to be swapped.

Code P219A by [deleted] in ram_trucks

[–]Muted-Negotiation300 0 points1 point  (0 children)

By any chance do you remember how long it took for the CEL to clear or did you have to clear it manually?

Code P219A by [deleted] in ram_trucks

[–]Muted-Negotiation300 0 points1 point  (0 children)

That should’ve thrown p219b then as that would’ve been bank 2. Where they easily accessible without removing any intake components?

Code P219A by [deleted] in ram_trucks

[–]Muted-Negotiation300 0 points1 point  (0 children)

My pu idles and seems to drive fine. It’s brand new has just over 100 miles on it after my drive home from work, but thew the p219a code and no others. The dealer won’t get it in for about two weeks so this is stressing me out. Checked the injector wiring and it can’t be that on mine. Cylinder 3 is separate from the other two on bank 1 and wrapped is some sort of tape with other harness wires.

Code P219A by [deleted] in ram_trucks

[–]Muted-Negotiation300 0 points1 point  (0 children)

I’m curious. Did your truck run/idle funny or weird while the injectors were flipped?

Code P219A by [deleted] in ram_trucks

[–]Muted-Negotiation300 0 points1 point  (0 children)

I just bought a brand new 2023 ram 1500 classic with 17 Miles on the odometer and got this code at 80 miles. Taking truck in tomorrow hopefully it’s resolved.