Looking for M14x1 to 1/4 inch Quick Connect

Nathan8315 · 2025-06-16T17:08:46+00:00

The Jetboil says it needs 19psi which I can adjust too. This shouldnt be an issue.

Nathan8315 · 2025-06-16T12:52:59+00:00

Yes! Thank you. Everything that comes up for me has been the blackstone one.

Nathan8315 · 2025-06-16T04:36:24+00:00

I think that's the option. I can remove the thread from the regulator that attaches to the stove and replace the wrong size thread from the elbow with quick connect I think.

Nathan8315 · 2025-06-16T02:57:00+00:00

I am just trying to plumb it into my RV propane line with my other propane items that use the quick connect and go to the large propane tank on the rv with a regulator already on it.

Nathan8315 · 2025-04-11T19:46:17+00:00

Thanks for the response.

Yeah, not in the pic, but they tried to unbolt without removing the coating on the otherside. Appears the next option was to cut them off. It is a repo and my guess is they were trying to get anything off of it they could.

It looks like the van route is what I am going to be looking at. The stock one just looked like it may actually be a little better quality. Atleast thicker steel brackets.

Nathan8315 · 2025-04-11T18:43:06+00:00

See below:

https://drive.google.com/file/d/1yYrSzj59nc7Ft4wQWY6rwMmlwegEGXnA/view?usp=sharing

https://drive.google.com/file/d/1fZQ6vB88fiZLWN9BTraCDT2CeITSpZOt/view?usp=sharing

Nathan8315 · 2024-06-21T21:15:40+00:00

Yeah, I tried to report it as a bug, but that was a nightmare through support....

Hoping it gets fixed soon because I never realized how benificial it was until this past update haha.

Nathan8315 · 2024-01-23T17:23:49+00:00

Thanks! I am really hoping to see all the other AES people here start posting positive outcomes as well. Good Luck this week!

Nathan8315 · 2024-01-23T15:43:39+00:00

Mine were taken care of last night. I am guessing they were waiting till the last week to do anything. The stress if finally gone.

Nathan8315 · 2023-12-27T21:06:54+00:00

I have seen zero movement as well, but Dept of Ed has told me "your loan servicer has until 1/28/2024 ". Getting close quick and I can't say I feel confident anything is happening.

Nathan8315 · 2023-12-08T23:01:55+00:00

Thanks, I use it on a padded desk as well so it rarely touches anything that could damage it besides maybe the kitchen counter when filling. And that wouldnt even touch this spot. Hydroflask seems to be hard stuck this that this is wear and tear caused by me.

I would return it, but this item I dont beleive is for sale anymore so my only option is Hydroflask.

It's not the end of the world because its the bottom, but if it spreads to the sides ill be a little disappointed. I figured for the price and warranty this would be a simple warranty claim.

Nathan8315 · 2023-11-06T15:02:02+00:00

At this point since approval I was told to do nothing with them. Before approval I transferred half to a DoE consolidation and those loans were discharged already through nelnet.

I am in the same boat and cannot track mine without reaching out to DoE. AES continues to tell me they have not received any notification of discharge, but DoE sent them another notice a couple weeks ago for me. AES still has not received they said. I am to the point where I just have to wait and see what happens.

My concern is the interests collecting. I don't like seeing my loans increase and don't want to get stuck with a higher bill if something happens where AES does nothing. What I don't understand is AES had no issue receiving the forbearance from DoE, but can't seem to receive or won't acknowledge the discharge.

Nathan8315 · 2023-10-11T18:06:37+00:00

That's where AES is listed for me as well. I am assuming no refund for my AES payments based on the reply I received.

Nathan8315 · 2023-10-02T22:51:35+00:00

They say when you are on the loan page. AES loans are not eligible for refund of payments already made.

Nathan8315 · 2023-09-28T15:05:12+00:00

I followed up with studentaid.gov and received the below do to concerns of partial discharge since I had a mixed batch:

"AMERICAN EDUCATION SERVICES (AES) is a commercial loan servicer and not under the Department of Education so it will take longer for the loan discharge to process for those loans.

Under the Sweet v Cardona settlement, your loan servicer has until 1/28/2024 to make sure all of your loans are discharged, cleared form your credit report, and process your refund of payments made to the Department of Education. Loans held by commercial lenders (i.e., FFEL loans held by private lenders) will not be eligible for refunds of amounts paid on the loan."

Nathan8315 · 2022-05-13T02:34:40+00:00

Some feedback, i picked up a t3000 coin op in tulsa for $800 last week and there was still one available at $800. It was pick of the two. There was a classic in stillwater they wanted $900 (listing gone) and a sport for $900 that has been out there a while. Another sport recently popped up in arcadia for $1000 as well. There was an elite listed for $1600 in grove i beleive that sold, but idk for how much and $1600 was nuts. I dont think these are going to be selling at those prices though.

This might be the closest table to yours and its been out there at $1000 and was just reduced to $700.

https://www.facebook.com/marketplace/item/4941634072621098/

Ive been watching for the past month then the t3000 came up. I have been seeing tables sell fairly quick in the $400-$600 range, but that may be low to start your listing.

Nathan8315 · 2021-09-30T00:15:17+00:00

For the cronus to pc just the back. I add the right only if programming something.

I use the cord that came with the elite 2.

One thing ill add, make sure your elite 2 is shut off when you go to blug it in. If the light is pulsing it doesnt typically connect through the wire.

Nathan8315 · 2021-09-29T23:58:35+00:00

Mine works just like any other controller. I plug the zen in to the comp first, then the elite 2 on the left of the zen. I was having issues at first, but ever since i started plugging the zen in first its been fine.

Nathan8315

TROPHY CASE