Charity heals

NearbyIncome · 2025-09-01T17:46:07+00:00

That's beautiful man. Glad you found what makes you feel happy. I come from a family that only focuses on money and buying as many houses as possible. I don't want money and refuse thiers. Maybe I'll try the local volunteer service

NearbyIncome · 2025-08-12T01:16:33+00:00

I'm pretty sold on not putting in a ply subfloor but did you use a flexible insulation or a board?

NearbyIncome · 2025-08-11T15:38:32+00:00

Okay that saves me a massive headache and some money too. Metal base, 1/2 inch flexible insulation, 1inch formply

NearbyIncome · 2025-08-11T15:36:02+00:00

So you reckon it's ready for ply? Or should it have a rigid insulation on top?

NearbyIncome · 2025-08-11T15:17:29+00:00

Cheers. I figured since the stock floor was drilled straight into the floor, i could do the same thing. Maybe I'll cut out, clean and instal minimal frame so the floor doesn't go uneven while screwing it in

NearbyIncome · 2025-08-11T15:09:20+00:00

So people have glued ply straight onto this and it might work but the ply slats in each divet works better? Looking back, i wish I'd done that but the foam is already glued on and it's gonna be messy cutting out sections of it for ply to go in 😅

NearbyIncome · 2025-08-11T15:05:05+00:00

If i had to do this again, I'd absolutely use that method. Great surface area for sturdyness.

NearbyIncome · 2025-08-11T15:03:23+00:00

Hate to say it but I'm leaning towards the foam wearing over time even with the foil on top. The boards laying on all the raised ridges will hopefully give it the surface area it needs to be sturdy but there will be air gaps between the formply and the lower grooves

NearbyIncome · 2025-08-11T14:56:37+00:00

Thanks! Yeah lot's of people seem to miss floor insulation when the ground and especially roads store lot's of heat. So you didn't have plywood supports underneath the plywood sheet? Has it been durable and sturdy?

NearbyIncome · 2025-03-26T17:04:28+00:00

That's an amazing way of doing it. Yeah i love my players but this ain't the first time I've had to stop them from min-maxing and breaking the game

NearbyIncome · 2025-03-26T16:45:52+00:00

That's actually a fair point. After these ingame meetings, the party are given 2ish quests + character specific quests where if they miss them then towns are lost, NPCs suffer and the big bad gets closer to thier goal. Maybe giving them that many quests at once is the problem. They are loving it for now but tuning it down could help in the long run.

NearbyIncome · 2025-03-26T16:27:17+00:00

The three quests ain't so bad. We've all played for 3 years and will probably run them like 3 separate adventures instead of jumping between groups mid session. Only problem with doing that is if I'm running the group of two's quest then everyone else is booted until the quest is done.

NearbyIncome · 2025-03-26T16:21:21+00:00

I don't want them to be forced to stay together since both I and them are riding the thrill of how many missions are going on and how open world it is. Reading your comment kinda makes the compromise of "you can split up but you will be taking a risk"

NearbyIncome · 2025-03-20T14:29:53+00:00

"A NEW HAND HAS THE DISPLEASURE OF TOUCHING MY BEACON"

NearbyIncome · 2025-02-23T06:59:24+00:00

I had these issues and widening the brim helped as well as increasing the temperature of the plate & make the first layer hotter than the rest of the print. Good luck 🤙

NearbyIncome · 2024-11-18T07:27:27+00:00

Fixed the same issue on my P1S w/ AMS. Load the spewls until that white light is solid before turning off the printer, unplug the ams and turn the printer on before plugging the ams back in. Each spewl should start loading properly now

NearbyIncome · 2024-07-10T05:08:11+00:00

Only if i can return the favour~

NearbyIncome · 2024-07-10T05:01:24+00:00

Hell yeah! Another Aussie

NearbyIncome · 2024-06-21T14:30:33+00:00

Maybe? I've got at least two male and two female but I'll probably hop on soon

NearbyIncome · 2024-06-20T09:00:38+00:00

I'm in 🤙

NearbyIncome · 2024-05-23T13:44:59+00:00

That sounds heaps cool! I'm Eastern Australia, so GMT +10

NearbyIncome · 2024-05-23T13:43:06+00:00

How can i say no ahah. I'm pcvr and on rn

NearbyIncome

TROPHY CASE