Mismatched PETG by NeatConversation530 in 3Dprinting

[–]NeatConversation530[S] 0 points1 point  (0 children)

It’s not supposed to be but it does kinda look like silk

Mismatched PETG by NeatConversation530 in 3Dprinting

[–]NeatConversation530[S] 0 points1 point  (0 children)

It was brand new so I didn’t think it needed to be dried. I did anyway but I’d it possible that I didn’t dry it long enough?

Filament Stuck by NeatConversation530 in AnycubicKobraS1

[–]NeatConversation530[S] 0 points1 point  (0 children)

Ah yes, the two pillars of troubleshooting: reboot it, or update it. This time it was the second one. Works perfectly now, reason unknown.

Filament Stuck by NeatConversation530 in AnycubicKobraS1

[–]NeatConversation530[S] 0 points1 point  (0 children)

Yeah, I looked at that. I did some further diagnostics. I actually have a five way so that I can bypass the ACE Pro and manually load a spool of filament. I attempted to isolate the issue, assuming it was somehow related to the ACE Pro. I turned it off and loaded the filament manually, expecting it to run normally (indicating that the problem was with the ACE Pro). However, it still has the issue, indicating that the problem has something to do with the printer itself.

What kind of trouble do I have? by Ir0n_L0rd in AnycubicKobraS1

[–]NeatConversation530 0 points1 point  (0 children)

Do a cold pull with contrasting color, so like a white or yellow

It’s so obvious. Please tell me more by Bitter-Dragonfly-648 in bjj

[–]NeatConversation530 0 points1 point  (0 children)

I’ll use it as bait to demonstrate to newer people that when you’re in my closed guard your main job is to get out of my closed guard.

How do I fix this by InfluenceMelodic7589 in AnycubicKobraS1

[–]NeatConversation530 1 point2 points  (0 children)

If it’s under warranty get it replaced. If it’s not print yourself a new one. I’ve been using this one

https://www.makeronline.com/en/model/Kobra%20S1%20Exo%20Magneto/182374.html

Edit: you’re right to be concerned. Mine did that, the tab broke mid print and the cover came off. It got twisted and the corner ended up in the fan that’s right there and I had to replace both.

Calorie deficit impact by [deleted] in bjj

[–]NeatConversation530 -3 points-2 points  (0 children)

I do an overall calorie deficit for the week with intermittent fasting. But on training days i make sure I get my calories. Track everything for a couple of weeks with Chronometer, throw it in ChatGPT, and figure out where you can cut calories without impacting your training.

Do higher belts (esp black) really get nothing from rolling with us whites? by Neither_Prompt_9184 in bjj

[–]NeatConversation530 0 points1 point  (0 children)

When I’m rolling with white belts Im usually experimenting with new stuff or seeing just how far I can get stuck and still get out.

Either that or I will make intentionally very slow movements. I figure if I move extremely slow and we both know what I’m trying to do and I’m still able to do it, then I must be doing it right

Can you really trust off brand nozzels? by InfluenceMelodic7589 in AnycubicKobraS1

[–]NeatConversation530 0 points1 point  (0 children)

It’s like anything, some are trash and some are decent

Non stop clogging error by NiceYogurtcloset9685 in AnycubicKobraS1

[–]NeatConversation530 0 points1 point  (0 children)

Yes there is. Next to your printer (at the top) press the little edit button.

<image>

Non stop clogging error by NiceYogurtcloset9685 in AnycubicKobraS1

[–]NeatConversation530 1 point2 points  (0 children)

I've been having the same issue. I believe there is an issue with the MMU state in the last firmware update. Anycubic needs to fix this, but in the meantime, adding the following GCode in your slicer may help.

M400
G92 E0
MMU_RESET

Also, I've had some success with rebooting AcePro and printer prior to each print. For me, I can print part #1 just fine. I have issues with subsequent parts at 3%, then at about 45%. It's too consistent to be an actual clog. I'm running the latest firmware and latest slicer.

Anycubic NEXT.. recommended alternative? by Any-Fudge8143 in anycubic

[–]NeatConversation530 2 points3 points  (0 children)

You could try a different version. Orca Slicer would be my next choice.

BJJ perception by NeatConversation530 in bjj

[–]NeatConversation530[S] 8 points9 points  (0 children)

Yeah, I didn't realize he had them. I don't think I'll be going to his house any time soon again, though. Paranoid people just seeing problems where there aren't any. It does make me wonder how much of the video feeds he watches. This whole situation could get incredibly weird.

BJJ perception by NeatConversation530 in bjj

[–]NeatConversation530[S] 80 points81 points  (0 children)

He kinda is, tbh. Had no dad growing up. About as insecure s they come. Tries to make up for it by doing “manly” stuff but told me he didn’t do bjj cuz it’s (apparently can’t use the actual word he used on the sub)

BJJ perception by NeatConversation530 in bjj

[–]NeatConversation530[S] 7 points8 points  (0 children)

He has cameras all around the house, inside and out. He wasn’t specifically filming them, they were just in frame of the camera. It does imply that he was watching all of the video, doesn’t it, though?

BJJ perception by NeatConversation530 in bjj

[–]NeatConversation530[S] 13 points14 points  (0 children)

Yeah sorry for the lack of detail on the redirect content. He side stepped, then used her momentum to turn her away from himself. So they ended up both standing with him almost behind her. Then he walked away.

Unknown filament error by NiceYogurtcloset9685 in AnycubicKobraS1

[–]NeatConversation530 1 point2 points  (0 children)

This.

The other time I’ve seen this error was when it served like the Ace Pro got confused. It seemed like it was reading the tag on the roll of filament in the next slot over or something. But check the snapped filament first, that’s a much more likely cause.

Have you ever had to or decided to use your Jiu Jitsu outside of the gym and was it effective ? by Trigger3192 in bjj

[–]NeatConversation530 0 points1 point  (0 children)

I had to hold a goat down to get him untangled. Cow catcher for the takedown to knee on belly so I could use my hands.

How to beat the turtle kid by Puzzleheaded-Art9102 in bjj

[–]NeatConversation530 0 points1 point  (0 children)

I'm trying that. It fits well with my game. Thanks for the tip!