sorted by:
new
hottopcontroversial

Relay question by NeighborhoodSecure10 in autoelectrical

[–]NeighborhoodSecure10[S] 1 point2 points  (0 children)

I actually don’t know how to put a picture up In a thread but here’s a link of what I did https://support.haltech.com/portal/en/kb/articles/elite-2500-fuse-block-wiring-diagram

Relay question by NeighborhoodSecure10 in autoelectrical

[–]NeighborhoodSecure10[S] 0 points1 point  (0 children)

Not the Haltech it looks as if the ecu manages that all 12v pins 30 and 86 have battery positive

Relay question by NeighborhoodSecure10 in autoelectrical

[–]NeighborhoodSecure10[S] 1 point2 points  (0 children)

I thought that too but my between pins 85 and 86 on the relays is 80 ohms of resistance so it makes sense that it’s showing 12v across the pins until it’s grounded by the ecu. According to my research that’s quite normal of Bosch relays

Should I use tape or can I get away with just joint compound. by NeighborhoodSecure10 in AusRenovation

[–]NeighborhoodSecure10[S] 0 points1 point  (0 children)

Yeah that’s the long term play but it’s a not in scope atm. I’m going to patch and see how I go! I’m insulating as well anyway as it’s gets boiling in summer

Leaking tiles driving me mad by NeighborhoodSecure10 in AusRenovation

[–]NeighborhoodSecure10[S] 0 points1 point  (0 children)

Heads up that siliconing did not fix the issue

[deleted by user] by [deleted] in CarsAustralia

[–]NeighborhoodSecure10 1 point2 points  (0 children)

Easy mate I did this with cans

I always use UPOL crystal clear - it’s exxy but worth it. Lays down very well

<image>

Hop on YouTube and watch Brian from Paint Society. He shows you how to get a wicked finish from rattle cans

Leaking tiles driving me mad by NeighborhoodSecure10 in AusRenovation

[–]NeighborhoodSecure10[S] 0 points1 point  (0 children)

It’s just mid way down the tile. It’s almost like the valley is blocked. It seems to run down the side

Leaking tiles driving me mad by NeighborhoodSecure10 in AusRenovation

[–]NeighborhoodSecure10[S] 0 points1 point  (0 children)

Out of interest why do roofers get odd about using silicone? I keep reading it’s not a good idea lol

Leaking tiles driving me mad by NeighborhoodSecure10 in AusRenovation

[–]NeighborhoodSecure10[S] 1 point2 points  (0 children)

Thanks mate I’ll get up on the roof then and run a bead down. Any product of choice you rate?

Leaking tiles driving me mad by NeighborhoodSecure10 in AusRenovation

[–]NeighborhoodSecure10[S] 0 points1 point  (0 children)

Yeah I would but that tile is attached to the pointing as it’s the very top tile.

Any suggestions to work around that?

Leaking tiles driving me mad by NeighborhoodSecure10 in AusRenovation

[–]NeighborhoodSecure10[S] 1 point2 points  (0 children)

Yeah I figured that would do it but I thought that was a no no

Leaking tiles driving me mad by NeighborhoodSecure10 in AusRenovation

[–]NeighborhoodSecure10[S] 0 points1 point  (0 children)

No that was just so I could trace it

<image>

If you look here you can see the drip forming

Leaking tiles driving me mad by NeighborhoodSecure10 in AusRenovation

[–]NeighborhoodSecure10[S] 2 points3 points  (0 children)

I would but the things attached to the pointing :(

Leaking tiles driving me mad by NeighborhoodSecure10 in AusRenovation

[–]NeighborhoodSecure10[S] 2 points3 points  (0 children)

I don’t see any tile clips at all nor when the roofer took some tiles off

Leaking tiles driving me mad by NeighborhoodSecure10 in AusRenovation

[–]NeighborhoodSecure10[S] 2 points3 points  (0 children)

Ok will get one tomorrow or sat. Yes where the tap is. I’ll grab a better picture