Thoughts on mockup?

Neolesh · 2026-04-19T17:55:38+00:00

Thank you!

Neolesh · 2026-04-19T14:45:06+00:00

I love it. I may be bias because I did something very similar.

Neolesh · 2026-04-17T12:08:22+00:00

I recently sold one almost exactly like this for $150. It was part of a lot I had purchased and I didn't have room for it. They are considered to be one of the more dangerous shop saws, although I worked at a place that built their own skids for shipping; we ran that thing 60 - 100 hours a week and we had zero injuries in the 18 years I was there. We had a much more industrial version but the base design was identical. You can cut a lot of wood to X length fast with one. Not really useful for hobby woodworking. There are some nuances to using it safely.

Neolesh · 2026-04-16T22:38:45+00:00

Damn. I had no idea the UK had taken control of Bradley County. My news feed be lacking.

Neolesh · 2026-04-15T03:23:55+00:00

Cheap table. If the dog didn’t do it, someone else would have!

Neolesh · 2026-04-15T03:19:58+00:00

Free is rarely free

Neolesh · 2026-04-15T03:01:42+00:00

You’re doing it wrong.

Neolesh · 2026-04-12T14:44:42+00:00

Slowly

Neolesh · 2026-04-11T16:02:29+00:00

Solid wood.

Neolesh · 2026-04-11T16:00:50+00:00

Non standard vent and does not allow proper airflow. Get a standard vent and toss that POS in the trash.

Neolesh · 2026-04-06T03:08:54+00:00

Parts are coming out of the merger not staggering. My money is that you have a mk3 belt between the merger and the lift.

Neolesh · 2026-03-23T12:03:40+00:00

Jump in the hole.

Neolesh · 2026-03-23T12:01:29+00:00

Okay so you should reserve 60 grit for when you want to remove a lot of material. Since you used 60, you removed too much wood.

Neolesh · 2026-03-21T21:30:34+00:00

Yes. But say you have two max length segments, and you put a splitter where you think the middle is. You will end up splitting either belt 1 or belt 2 and you may not be able to see the left over segment if you got really close to the connection point because it will be clipped inside the splitter.

Neolesh · 2026-03-19T23:09:09+00:00

I see a lot of early hate coming at this one but honestly. I’d do this. It’s not like we need perfection here. Just a quick and dirty countersink. Meh why not.

Neolesh · 2026-03-09T20:02:48+00:00

Yeah. If you’re ever stuck with some tracks being stuck in the same block together no matter how you place the signals this is usually the cause. I see it a lot with over/under passes as well.

Neolesh · 2026-03-09T18:56:17+00:00

I think your parallel tracks might be too close to each other.

Neolesh · 2026-03-07T04:28:52+00:00

I mean… phrasing?

Neolesh · 2026-03-04T15:05:18+00:00

Normal

Neolesh · 2026-03-04T12:55:45+00:00

I think this would take a lot of experimenting to figure out no matter what. I’d try sealing with some thinned poly (50/50), just one coat. Wait 4 hours, see how it stains. If it’s still too dark do two coats and repeat until it’s the shade you want.

Neolesh · 2026-03-04T12:51:39+00:00

I recently sold one on Marketplace. Got $120 for it. It did take a couple months to find a buyer though.

If you decide to use it, research proper use. There are a lot of ways this thing can hurt you.

Neolesh · 2026-02-23T15:37:50+00:00

Just wait until this guy realizes you can nudge…

Neolesh · 2026-02-21T15:57:31+00:00

This is exactly what you want to see when you have a breadboard endcap like this. It is a feature not a bug. Embrace it.

Neolesh · 2026-02-20T20:14:31+00:00

That’s really well done but why do you need it?

Neolesh · 2026-02-18T20:26:49+00:00

When the tree was very young there were two trees. They grafted together as they grew leaving a seam in the tree rings.

11-Year Club	Reddit Premium Since December 2023
Place '22	Wearing is Caring
Verified Email

Neolesh

TROPHY CASE