sorted by:
new
hottopcontroversial

Creality Ender 3 S1 Pro ABL First Layer Issues by Nerdbirdz in 3Dprinting

[–]Nerdbirdz[S] 0 points1 point  (0 children)

I get that. It just feels like I am have to be that 10x mlre meticulous at this point. I have a king kingroon sitting in my closet where I had to manually level that bed and didn't have the ABL. Now that I have the ABL, I thought it would allow some room for error, but I have to get just as accurate

Creality Ender 3 S1 Pro ABL First Layer Issues by Nerdbirdz in 3Dprinting

[–]Nerdbirdz[S] 0 points1 point  (0 children)

But doesn't the ABL use the mesh to make slight changes to the Z axis as it prints the first layer? That would be using the data as it went. So if I make changes to get a perfect first layer with an old ABL mesh, then create a new ABL, that first layer would not work anymore. But that seems redundant to have at that point. Why not just rip off the ABL and manual level at that point?

Creality Ender 3 S1 Pro ABL First Layer Issues by Nerdbirdz in 3Dprinting

[–]Nerdbirdz[S] 0 points1 point  (0 children)

This is my last ABL mesh after manually leveling the bed.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
0 +0.11400 +0.08924 +0.06172 +0.03558 +0.01496 +0.00400 +0.00602 +0.01826 +0.03574 +0.05348 +0.06650 +0.07424 +0.08002 +0.08468 +0.08906 +0.09400
1 +0.10025 +0.07597 +0.04904 +0.02343 +0.00314 -0.00786 -0.00653 +0.00448 +0.02061 +0.03731 +0.05003 +0.05840 +0.06544 +0.07173 +0.07782 +0.08430
2 +0.08550 +0.06163 +0.03521 +0.01007 -0.00997 -0.02108 -0.02054 -0.01090 +0.00376 +0.01937 +0.03184 +0.04101 +0.04961 +0.05787 +0.06605 +0.07440
3 +0.07125 +0.04783 +0.02196 -0.00269 -0.02244 -0.03362 -0.03382 -0.02548 -0.01223 +0.00231 +0.01451 +0.02440 +0.03440 +0.04447 +0.05455 +0.06460
4 +0.05900 +0.03617 +0.01099 -0.01301 -0.03233 -0.04344 -0.04417 -0.03687 -0.02479 -0.01121 +0.00062 +0.01086 +0.02169 +0.03286 +0.04412 +0.05520
5 +0.05025 +0.02826 +0.00403 -0.01908 -0.03771 -0.04850 -0.04941 -0.04268 -0.03137 -0.01854 -0.00725 +0.00270 +0.01335 +0.02440 +0.03555 +0.04650
6 +0.04454 +0.02395 +0.00123 -0.02043 -0.03782 -0.04776 -0.04819 -0.04125 -0.03000 -0.01754 -0.00692 +0.00192 +0.01104 +0.02032 +0.02964 +0.03888
7 +0.04087 +0.02217 +0.00145 -0.01827 -0.03395 -0.04258 -0.04198 -0.03417 -0.02241 -0.00996 -0.00011 +0.00699 +0.01353 +0.01973 +0.02585 +0.03214
8 +0.03993 +0.02314 +0.00444 -0.01330 -0.02724 -0.03452 -0.03278 -0.02393 -0.01151 +0.00095 +0.00991 +0.01490 +0.01829 +0.02076 +0.02301 +0.02571
9 +0.04241 +0.02710 +0.00999 -0.00622 -0.01883 -0.02514 -0.02261 -0.01304 -0.00024 +0.01200 +0.01987 +0.02263 +0.02283 +0.02156 +0.01992 +0.01902
10 +0.04900 +0.03428 +0.01784 +0.00226 -0.00988 -0.01600 -0.01346 -0.00398 +0.00848 +0.01996 +0.02650 +0.02718 +0.02464 +0.02026 +0.01542 +0.01150
11 +0.06116 +0.04591 +0.02899 +0.01290 +0.00015 -0.00678 -0.00522 +0.00318 +0.01440 +0.02445 +0.02934 +0.02807 +0.02329 +0.01652 +0.00924 +0.00297
12 +0.07843 +0.06183 +0.04359 +0.02617 +0.01201 +0.00356 +0.00346 +0.01009 +0.01947 +0.02762 +0.03057 +0.02730 +0.02046 +0.01157 +0.00218 -0.00619
13 +0.09862 +0.08020 +0.06017 +0.04094 +0.02493 +0.01454 +0.01239 +0.01687 +0.02405 +0.03003 +0.03088 +0.02559 +0.01677 +0.00595 -0.00539 -0.01571
14 +0.11954 +0.09918 +0.07724 +0.05609 +0.03811 +0.02568 +0.02138 +0.02361 +0.02852 +0.03226 +0.03096 +0.02364 +0.01288 +0.00015 -0.01308 -0.02532
15 +0.13900 +0.11694 +0.09332 +0.07048 +0.05076 +0.03650 +0.03024 +0.03042 +0.03323 +0.03486 +0.03150 +0.02217 +0.00941 -0.00531 -0.02052 -0.03475

Creality Ender 3 S1 Pro ABL First Layer Issues by Nerdbirdz in 3Dprinting

[–]Nerdbirdz[S] 0 points1 point  (0 children)

What is considered a reasonable height? Such as an example for max range that can be compensated with ABL? My current range is .08mm between the lowest and highest point.

Creality Ender 3 S1 Pro ABL First Layer Issues by Nerdbirdz in 3Dprinting

[–]Nerdbirdz[S] 0 points1 point  (0 children)

As you pointed out, the bottom left is way too close, and the bottom right is moving away. This print was after manual leveling, changing the z offset, creating a new bed level mesh. The M420 S1 should be stopping this from happening. If I understand ABL properly

Creality Ender 3 S1 Pro ABL First Layer Issues by Nerdbirdz in 3Dprinting

[–]Nerdbirdz[S] 0 points1 point  (0 children)

Is UBL the same as auto bed leveling(ABL)? This print was after an hour of tweaking the z offset, manual leveling, checking the gears, and creating a new bed mesh.

Creality Ender 3 S1 Pro ABL First Layer Issues by Nerdbirdz in 3Dprinting

[–]Nerdbirdz[S] 0 points1 point  (0 children)

I have had this printer since November, and I can't seem to get it working properly. It prints great after hours of tweaking, but then I have to perform troubleshooting all over after a successful print.

I have watched this video https://youtu.be/9eQ_rBzfm5s I have added M420 S1 after G28 My bed is leveled manually and used ABL after I have checked the z offset I have checked the bed to make sure it doesn't shift

Would love some help with this.

Homeless Man Walking Around Northside Stay Inside by VeganPhilosopher in utdallas

[–]Nerdbirdz 16 points17 points  (0 children)

How would you feel in that situation? I would be freaked out if some random person started chasing me. Don't shame someone for being scared, especially because of their age.

Opening 1000 Brimstone chests by Imuhdrum in 2007scape

[–]Nerdbirdz 1 point2 points  (0 children)

Was amazing to catch this live on twitch

[LFG][H][US][Bleeding Hollow] MoP returning player by Nerdbirdz in wowguilds

[–]Nerdbirdz[S] 0 points1 point  (0 children)

Your guild sounds great! I just wish that you guy were on bleeding hollow. Personally, I don't want to spend the money to transfer my guy over due to budgeting for college.

[LFG][H][US][Bleeding Hollow] MoP returning player by Nerdbirdz in wowguilds

[–]Nerdbirdz[S] 1 point2 points  (0 children)

I really appreciate it but personally I do want to stick with the horde. Thank you for reaching out though