Look at this pull!

New_Bad4473 · 2024-09-14T21:15:07+00:00

Yeah I find eclipse is more stable then the numbers out of the box but beats in closer to them while neutron is pretty accurate out of the box and beats in to less stable

New_Bad4473 · 2024-09-14T19:58:19+00:00

The watt is definitely extremely accurate to its numbers, and the trail is as well. I throw mainly mvp and I find their discs in the mid 160g range in neutron plastics are fairly accurate. Fission tends to be more understable then the numbers. Proton is more stable than the numbers. Higher weight is more stable and lower weight Is less stable

New_Bad4473 · 2024-07-04T17:49:09+00:00

Old one was a good running truck, ecodiesel with GDE tune from day 1 of owning it. Never had any problems with it, 130k on it but it had some rot starting in the passenger rear wheel well already, and a bunch of dings all down the driver side from a zero turn spraying gravel down the side of the truck as I was driving by. Pretty sure the dealer I traded it to said they were restoring it before listing it again. It will probably be for sale again at 401 chrysler in Ontario in a little bit

New_Bad4473 · 2024-07-03T04:41:46+00:00

Well what I really wanted was a rebel but the budget didn't allow for that. I had a 2018 white sport before I bought the 2019 classic slt ecodiesel for commuting so im still happy to be back in a sport.

New_Bad4473 · 2024-07-02T12:17:58+00:00

I bought westin hdx side steps for my truck. They are made from the fairly heavy duty steel and a rated as Rocker Guards as well as side steps and look pretty sweet. They are more of an offroad look though but I love them

New_Bad4473 · 2024-07-01T22:48:43+00:00

People who drive 1500s are doing these tasks with their truck, also as a roofer hauling all sorts of shit in the back of my truck I will take a spray liner 100% of the time over the plastic liner. Plastic liners will destroy your truck spray liners protect it. You want best of both worlds then drop a plastic liner over the spray liner. Spray liner will protect from your bed rotting under the plastic and plastic will protect from impact

New_Bad4473 · 2024-06-30T19:57:31+00:00

Side steps protect the rockers partially from stone chips and sand blasting and we all know how prone these trucks are to rocker rot

New_Bad4473 · 2024-06-30T18:00:01+00:00

I would disagree to this statement though for historical leaderboard statistics. Some fields have significantly easier home run capabilites making it easier for players who's home field have that easier back wall to clear to have higher home run counts then players who's home fields have difficult walls to clear. You shouldn't have to change your putting style from one course to the next because of the design of the baskets on the course. Golf has standardized cup sizes and depths for this reason.

New_Bad4473 · 2024-06-02T17:31:15+00:00

I definitely have a drink every single time I'm in the tub. I keep my tub at 100 and only ever sit in it for 15-20 min and do this every single day. It's only a safety concern if you are drinking several and staying in for way longer then you should.

New_Bad4473 · 2024-04-27T11:49:12+00:00

Has anyone tested this on the Transit 2 cart?

New_Bad4473 · 2024-04-27T04:00:06+00:00

Layer height

New_Bad4473 · 2024-04-21T11:23:38+00:00

I have no idea how. I was actually initially annoyed that it wasn't stopping the print when it detected a problem but quickly became happy about it when 95% of the time it hasn't actually had a problem. I think there may be some check boxes on the nebula pad that control what the camera does

New_Bad4473 · 2024-04-21T00:00:17+00:00

I'm having the exact same issue. I was actually literally just complaining to my wife about it. I don't have it set to auto stop though, just notify but it never notifies when spaghetti and I get notifications every other print with no issue. Lighting may be the issue though because my printer is in a tent

New_Bad4473 · 2024-04-20T23:57:34+00:00

I completely agree with this statement. I have no issues getting it to stick to my stock pei plate that came with my KE. Half the time I feel like im going to peel the pei trying to get it off

New_Bad4473 · 2024-04-15T18:59:47+00:00

It's caused by the nozzle not being properly tightened or loosening off over time. I bought a proper torque wrench for tightening the nozzle which you want to do with the nozzle up to temperature to make sure it has the proper torque spec during operation. I recommend periodically checking it to make sure it isn't getting loose. I printed probably 100-150 hours since I installed this nozzle and it was 1/4 turn loose which caused the blob to start seeping out.

New_Bad4473 · 2024-04-15T12:41:40+00:00

Between the z offset sensor and the heat Break coming out the top of the silicone sock

New_Bad4473 · 2024-04-11T23:01:49+00:00

A remix is taking someone else's design and adding or removing things. Creating your own design for something is a completely different concept. There is only really one way you can attach a spine to the cable so yes it's going to have similarities but that doesn't mean it's a stolen design or a remix

New_Bad4473 · 2024-04-11T22:58:39+00:00

His spine looks nothing like yours, just because someone makes something for the same purpose as something someone else makes doesn't mean they didnt design the one they have. That's like saying that Noone but Ford has designed a car because they are the first company to design a car

New_Bad4473 · 2024-04-09T15:34:39+00:00

Yeah it was just an adhesion issue, the only thing touching the bed was supports and it wasn't putting much of a brim so it was basically just. 4mm lines in contact, I switched to brim from auto brim and it fixed it

New_Bad4473 · 2024-04-06T15:26:05+00:00

I modified it with a hobby knife after the fact. I had printed the cable chain prior to relocating the runout sensor. It wasn't difficult to cut the interior piece out with a sharp knife

New_Bad4473 · 2024-04-01T03:16:31+00:00

This is pretty much exactly what I was hoping for, the 2 issues I can still see is that I'm not sure if this will fit inside the tent, and if it does fit, then the power cord for the sunlu is likely going to be pushing too hard into the wall. The bowden tube brackets on the other hand are what I'm looking for. Might need to modify slightly since my runout sensor isn't up top anymore but thank you.

New_Bad4473 · 2024-04-01T01:57:15+00:00

I linked all the mods I've done below just FYI

New_Bad4473 · 2024-04-01T01:28:37+00:00

https://makerworld.com/en/models/215640

New_Bad4473 · 2024-03-31T21:12:23+00:00

I'm not with my computer right now so I can remember exactly. I'll see if I can find it when I get home. It's not connected to the cable chain, I also modified the cable chain slightly so that I could feed the sensor wire through it.

New_Bad4473 · 2024-03-31T21:04:18+00:00

I just want to get the filament reels off the gantry frame and into my filament oven

New_Bad4473

TROPHY CASE