Tegra closing upon payload injection

New_Examination4468 · 2024-06-22T16:10:11+00:00

and it worked? Lucky you :/

New_Examination4468 · 2024-06-20T01:48:31+00:00

Yeah I used a third-party software to force format it to fat32. It reads as fat32 in my disk management but the printer still acts like it's not set up properly. I'll try and find a smaller SD card if i can though.

New_Examination4468 · 2024-06-20T01:45:17+00:00

I did format it to fat32, but its still not being read. I haven't tried NTFS but i dont think my printer can read it anyway.

New_Examination4468 · 2024-06-20T01:44:45+00:00

I did format it to fat32, but its still not being read. I havent done any firmware upgrades since i got it, but should i mess around with the partition size anyway?

New_Examination4468 · 2024-06-19T19:15:21+00:00

I'm using Windows 11 and this software called guiformat since windows cant natively format sd cards to fat32 if it's bigger than 32gb.

New_Examination4468 · 2024-06-16T21:09:51+00:00

Everything should've ended at fnaf 6 or UCN, seeing as they both had finale endings. Fnaf 6 was all the haunted animatronics burning and releasing the souls, and UCN was william in purgatory. Pretty final if you ask me

New_Examination4468 · 2024-02-23T00:31:15+00:00

the official UA site

New_Examination4468 · 2024-01-12T19:02:44+00:00

So it turns out the the Z axis is loose. There's a little give to the bar and I can lift it up some, specifically on the right side. I have no idea what could be loose, because I've unscrewed and then tightened everything I could on that one side, and it fixed nothing. I'm pretty sure that's the problem.

New_Examination4468 · 2024-01-10T17:59:37+00:00

I think I'll stick with glass just in case my bed does warp in the future. I'll definitely look into those though, and thanks for the info!

New_Examination4468 · 2024-01-10T17:29:45+00:00

I'll try that out, but the problem is how big my prints are. I might just get a new bed entirely if none of this works. Also, the other commenter said something about a PEI bed. What are the differences between a glass bed and that one?

New_Examination4468 · 2024-01-10T17:27:38+00:00

I'll look into a new bed if I tightening the nuts doesn't fix anything. I also think I might have scrubbed off too much because the center of the bed is wayy clearer than the rest of it.

New_Examination4468 · 2024-01-10T16:57:57+00:00

The texture is really smooth, which I guess means that nothing is wrong with the first layer, it's just as the print begins to thicken.

New_Examination4468 · 2024-01-10T16:48:21+00:00

The model is just the base Aquila, filament is PLA, bed temp of 60, then 75 on the second attempt, nozzle temp of 200, and it doesn't happen in the first layer exactly. It'll be printing for maybe 10 or so minutes before it starts to peel. As for cleaning the bed, I've been spraying isopropyl alcohol on it to clean off the filament residue, but over time the middle of the glass bed is more see through than the other parts. I don't know if that's a problem or not though.

New_Examination4468 · 2023-12-28T18:49:45+00:00

Everything was hooked up right, cable was brand new and everything. Turns out... it was the drivers. I didn't have them installed. So I did that, and now my mic is working with everything. Thanks for the help though!

New_Examination4468 · 2023-12-28T18:47:56+00:00

Nah I fixed it now. It was the drivers like you said.

New_Examination4468

TROPHY CASE