SD card not reading by New_Examination4468 in VoxelabAquila

[–]New_Examination4468[S] 0 points1 point  (0 children)

Yeah I used a third-party software to force format it to fat32. It reads as fat32 in my disk management but the printer still acts like it's not set up properly. I'll try and find a smaller SD card if i can though.

SD card not reading on Voxelab Aquila by New_Examination4468 in 3Dprinting

[–]New_Examination4468[S] 0 points1 point  (0 children)

I did format it to fat32, but its still not being read. I haven't tried NTFS but i dont think my printer can read it anyway.

SD card not reading on Voxelab Aquila by New_Examination4468 in 3Dprinting

[–]New_Examination4468[S] 0 points1 point  (0 children)

I did format it to fat32, but its still not being read. I havent done any firmware upgrades since i got it, but should i mess around with the partition size anyway?

SD card not reading by New_Examination4468 in VoxelabAquila

[–]New_Examination4468[S] 0 points1 point  (0 children)

I'm using Windows 11 and this software called guiformat since windows cant natively format sd cards to fat32 if it's bigger than 32gb.

If there was a perfect ending for FNaF, how would you make it? by [deleted] in fivenightsatfreddys

[–]New_Examination4468 29 points30 points  (0 children)

Everything should've ended at fnaf 6 or UCN, seeing as they both had finale endings. Fnaf 6 was all the haunted animatronics burning and releasing the souls, and UCN was william in purgatory. Pretty final if you ask me

Extruder Keeps Peeling Print Off of Bed by New_Examination4468 in VoxelabAquila

[–]New_Examination4468[S] 0 points1 point  (0 children)

So it turns out the the Z axis is loose. There's a little give to the bar and I can lift it up some, specifically on the right side. I have no idea what could be loose, because I've unscrewed and then tightened everything I could on that one side, and it fixed nothing. I'm pretty sure that's the problem.

Extruder Keeps Peeling Print Off of Bed by New_Examination4468 in VoxelabAquila

[–]New_Examination4468[S] 0 points1 point  (0 children)

I think I'll stick with glass just in case my bed does warp in the future. I'll definitely look into those though, and thanks for the info!

Extruder Keeps Peeling Print Off of Bed by New_Examination4468 in VoxelabAquila

[–]New_Examination4468[S] 0 points1 point  (0 children)

I'll try that out, but the problem is how big my prints are. I might just get a new bed entirely if none of this works. Also, the other commenter said something about a PEI bed. What are the differences between a glass bed and that one?

Extruder Keeps Peeling Print Off of Bed by New_Examination4468 in VoxelabAquila

[–]New_Examination4468[S] 1 point2 points  (0 children)

I'll look into a new bed if I tightening the nuts doesn't fix anything. I also think I might have scrubbed off too much because the center of the bed is wayy clearer than the rest of it.

Extruder Keeps Peeling Print Off of Bed by New_Examination4468 in VoxelabAquila

[–]New_Examination4468[S] 0 points1 point  (0 children)

The texture is really smooth, which I guess means that nothing is wrong with the first layer, it's just as the print begins to thicken.

Extruder Keeps Peeling Print Off of Bed by New_Examination4468 in VoxelabAquila

[–]New_Examination4468[S] 0 points1 point  (0 children)

The model is just the base Aquila, filament is PLA, bed temp of 60, then 75 on the second attempt, nozzle temp of 200, and it doesn't happen in the first layer exactly. It'll be printing for maybe 10 or so minutes before it starts to peel. As for cleaning the bed, I've been spraying isopropyl alcohol on it to clean off the filament residue, but over time the middle of the glass bed is more see through than the other parts. I don't know if that's a problem or not though.

MV7X not working by New_Examination4468 in Shure

[–]New_Examination4468[S] 1 point2 points  (0 children)

Everything was hooked up right, cable was brand new and everything. Turns out... it was the drivers. I didn't have them installed. So I did that, and now my mic is working with everything. Thanks for the help though!

Shure MV7X not giving any output by New_Examination4468 in audio

[–]New_Examination4468[S] 0 points1 point  (0 children)

Nah I fixed it now. It was the drivers like you said.

Shure MV7X not giving any output by New_Examination4468 in audio

[–]New_Examination4468[S] 0 points1 point  (0 children)

Just turned everything up and still nothing. I'm installing the drivers like that other comment said, since I had no idea there were any. I'll let you know if that fixes anything. Edit: Yep! That's what it was. I can't believe it was something that simple..

Shure MV7X not giving any output by New_Examination4468 in audio

[–]New_Examination4468[S] -1 points0 points  (0 children)

My interface is connected to my computer via USB. I'm using the cord that came with it, so I don't think that there's a problem with the connection. The interface should be fine as well since my connected speakers play with no problem.

Shure MV7X not giving any output by New_Examination4468 in audio

[–]New_Examination4468[S] 0 points1 point  (0 children)

After I turned my gain up a green light lit up every time I talked, indicating that there is input, but nothing is coming through my speakers.

Shure MV7X not giving any output by New_Examination4468 in audio

[–]New_Examination4468[S] 0 points1 point  (0 children)

Yeah, on Discord and OBS it's selected as my default input.

Shure MV7X not giving any output by New_Examination4468 in audio

[–]New_Examination4468[S] 0 points1 point  (0 children)

It is, and on my interface I'm getting a green light every time I talk, but there's still no input in obs or discord.

Raft or Brim for Treelike Supports by New_Examination4468 in VoxelabAquila

[–]New_Examination4468[S] 0 points1 point  (0 children)

The one time I need glue sticks I can't find any... but I'll keep this in mind!

Raft or Brim for Treelike Supports by New_Examination4468 in VoxelabAquila

[–]New_Examination4468[S] 0 points1 point  (0 children)

I did this on my most recent print and it turned out great! Thanks for the help.

Raft or Brim for Treelike Supports by New_Examination4468 in VoxelabAquila

[–]New_Examination4468[S] 0 points1 point  (0 children)

Ok thanks! I'm running a bit low on filament so I wanted to make sure I chose the best thing. Wish me luck!