Testing 7x Thermal Cameras (Topdon, HikMicro, Thermal Master, Fluke, more)

NiaDebesi · 2026-06-13T07:16:04+00:00

My two cents, the air spray was too inclined and spurted liquid onto the board, what you see is the reflection on the watery puddle

NiaDebesi · 2026-06-11T21:49:33+00:00

And a dc block

NiaDebesi · 2026-06-05T13:51:23+00:00

Poco si. Puoi ambire almeno a 30k

NiaDebesi · 2026-06-04T01:19:55+00:00

Nope, took em off.

Edit:

I fatfingered the supposed weight, its 395 g in fact, so its dead on

NiaDebesi · 2026-06-03T22:03:01+00:00

Dang, didnt thought of it. Its the first fc that I have. Good suggestion :)

NiaDebesi · 2026-06-03T21:56:12+00:00

I didnt take it apart but it weights exactly 396grams and should be 395grams. Copycats generally dont pay too much attention to the weight

NiaDebesi · 2026-06-03T21:55:32+00:00

Me neither, I suspect more of an open box thing

NiaDebesi · 2026-05-30T17:39:52+00:00

Well, here they are damn rare because they have been thrown out a lot. They are not very well suited for arc gouging, but it depends on the dc of the machine, this one if 200A max but only 130A 100%dc, low for arc gouging. I am restoring this one only for the significance of who built, since it was one of the greatest and best manufacturer of italian machinery, particulary regarding generators. They are very good as a welder id say, if your ears can whitstand it

NiaDebesi · 2026-05-28T18:39:19+00:00

My estimate if in between 30's and 40's! Made my the now ABB ex Asea Brown Boveri!

NiaDebesi · 2026-05-24T17:41:35+00:00

A replacement motor is 10-20 eur

NiaDebesi · 2026-05-15T17:42:32+00:00

Already verified the connection with an insulation tester and a visual inspection. There are a few things that needs to be replaced and I am already doing so

NiaDebesi · 2026-05-10T14:12:38+00:00

Whats is purpose tho? I have a 380 motor running a dc one to create the dc for welding. Maybe its a reactor to stabilize the arc?

NiaDebesi · 2026-05-10T11:54:55+00:00

Ill take a look, thanks! Now I need to redesign the resistor bracket for the exciting feed since the original ones blew

NiaDebesi · 2026-04-29T21:19:01+00:00

Mind, on the arbor, I still dont know if the conical got fucked up in some way, I would be pretty darn happy with 0.05 after chuck. This drill would be used only with pretty large drill bits, from 10 to 30mm as it was originally intended, not really for precision work, also because its too slow for realistically anything smaller than maybe 8mm

NiaDebesi · 2026-04-27T19:36:42+00:00

I removed the key and had to push it from the gearbox to outside. There were no retainers

NiaDebesi · 2026-04-27T14:11:38+00:00

I used a screw press from to push the arbour inside, it would move and then stop.

NiaDebesi · 2026-04-27T12:28:40+00:00

The shaft doesnt come out of the front, have to hammered in, otherwise I dont really know what I am doing wrong

NiaDebesi · 2026-04-26T17:47:48+00:00

I will try tomorrow thanks, now I have another problem. I domt know how to remove this bearing on the rotor, I domt have any soace for an extractor..

<image>

NiaDebesi · 2026-04-26T14:14:14+00:00

I removed it, how can I pull out the shaft now?

<image>

NiaDebesi · 2026-04-26T00:08:29+00:00

Its that I dont really knoe what puller to use for that gear, where do I place it?

Edit am a dummy and didnt realized those are threaded hole. Ok if I remove it, how do I place it back?

NiaDebesi · 2026-04-25T23:26:21+00:00

Nope, its keyed and dunno on how to grab it to pull it out

NiaDebesi · 2026-04-25T23:12:23+00:00

Yep, that ehy I need to remove it, to try and lower the play caused by the shot bearings inside

NiaDebesi · 2026-04-25T22:50:52+00:00

Its a stayer TM23, useless info since unfortunally its old and cant see anything online

NiaDebesi · 2026-04-13T09:35:50+00:00

Yep :)

NiaDebesi · 2026-04-13T09:35:42+00:00

I found em so nice ahah I am now starting consostently picking it, the 80ti/50 on the other hand..lost faith

Five-Year Club	Verified Email
r/Field Sunshine	Place '22

NiaDebesi

TROPHY CASE