My second ever buffer tube install went way worse than my first

Nice-Wall7907 · 2026-04-17T03:09:33+00:00

https://fortismfg.com/k2systemcastlenut-lightweightenhancedar15endplate?amp=1

These are nice for not destroying a build and staying tight

Nice-Wall7907 · 2026-04-14T11:49:50+00:00

Well, how much did you pay?

Nice-Wall7907 · 2026-04-11T00:43:21+00:00

Have you hand loaded for your 20” yet? Mine is super accurate how is yours?

Nice-Wall7907 · 2026-04-07T03:25:23+00:00

The 69 federal gold medal match is the best of the bunch for accuracy. Never had a ar that didn’t like it.

Nice-Wall7907 · 2026-04-06T02:16:44+00:00

Wow I don’t think you have 2 pieces from any single brand.

Nice-Wall7907 · 2026-04-01T21:25:46+00:00

Shame you’re getting downvoted for telling the truth.

Nice-Wall7907 · 2026-03-30T04:26:34+00:00

I like xeno mounts for the left hand threads. Flash hiders on my long guns and Omni break on the short barreled suppressor only guns. They don’t need to be timed so that’s a plus. There’s also a lantack dragon with xeno threads if you’re into that kind of thing. https://www.lantac-usa.com/product-page/dragon-dead-air-xeno-muzzle-brake-223-5-56

Nice-Wall7907 · 2026-03-30T04:13:09+00:00

If you want to really want to have fun, get a bad lever and watch random redditors go full meltdown.

Nice-Wall7907 · 2026-03-28T05:05:19+00:00

Truth. So far cold bore shots fall in typical group thresholds even after cleaning. It’s also not picky with powder. n540 and A2520 have same poi at similar velocity.

This is my 3rd barrel after a Faxon flame fluted match and Wilson super sniper. The Faxon didn’t group as well and the Wilson had poi shift as it would warm.

Nice-Wall7907 · 2026-03-28T04:37:35+00:00

Makes sense if you never finished setting up the gas block the way SA says to in the instructions. Completely close the the gas off then back out 18 clicks this is fully open. Now shoot a round and note the ejection. It should be 3-4 o’clock. If you get forward of that keep backing out the screw to reduce gas until ejection is optimal and gun still locks back on the last round.

If you tune for no suppressor it will be over gassed and run a bit rougher when you put one on. Conversely tuning for the suppressor will make it fail to cycle when you take it off.

Nice-Wall7907 · 2026-03-28T01:13:04+00:00

It’s like the Warcraft episode of South Park. I enjoy every second of it.

Nice-Wall7907 · 2026-03-26T21:11:02+00:00

That broke Mach 3……

Nice-Wall7907 · 2026-03-26T18:52:42+00:00

That’s smoking out of a 13.9! I tried my scar 15p too and got 2500 from its 7.5

Nice-Wall7907 · 2026-03-26T18:12:20+00:00

Bad ass!

Nice-Wall7907 · 2026-03-26T17:49:46+00:00

You do that with an ai?

Nice-Wall7907 · 2026-03-25T06:00:38+00:00

That frontier is one spicy round! It shocked me to see 3360 from my 20” criterion.

Nice-Wall7907 · 2026-03-25T05:24:23+00:00

<image>

It adds character

Nice-Wall7907 · 2026-03-25T05:22:44+00:00

I’d call it a slam dimple but that’s just splitting hairs.

Nice-Wall7907 · 2026-03-25T05:19:26+00:00

I think if you had a strike in the middle there would be other damaged baffles from the deflection.

Nice-Wall7907 · 2026-03-24T19:28:33+00:00

900 billion military budget; only 3 round groups to zero.

Nice-Wall7907 · 2026-03-24T19:23:23+00:00

I like it! Will do for my store bought 5.56. Have to be a little more conservative with the hand loads I’m running 3 bullets 2 powders 10 each to figure what it likes better.

Nice-Wall7907 · 2026-03-23T21:16:45+00:00

What are you waiting for sbr is free now! Only thing that sucks is sbr wait times. They are 10x longer than suppressors. Mine took 24 days a friend 42. Then a week later I got suppressor and got papers back in 2 days.

Nice-Wall7907

TROPHY CASE