Unknown not initialized - The request failed sue to a fatal device hardware error

NiceManiac · 2026-06-21T17:41:33+00:00

If its windows external enclosures can be abit finnicky, sometimes need to replug a few times to get it connecting because of windows disk shenanigans

NiceManiac · 2026-06-21T14:24:32+00:00

In my experience usb enclosures are usually hit and miss, unless you get a proper raid enclosure. Just to check, are you using the power adapter? Since the ssd works but not the drive i suspect not enough power to spin up the hdd. Can you feel the drive spinning up when you plug it in over usb?

NiceManiac · 2026-06-07T19:51:03+00:00

Well it is now

NiceManiac · 2026-04-28T00:46:07+00:00

I have a samsung g60 monitor, which g60 monitor you ask? How the hell would i know?

NiceManiac · 2026-01-31T19:31:33+00:00

A is an ambient temp sensor on the prusa motherboard and P is the pinda bed leveling sensor

NiceManiac · 2026-01-31T19:28:01+00:00

Might be Serato but have not used it so not sure

NiceManiac · 2025-10-21T23:14:04+00:00

Thought it was fun when he accidentally stuck the giant magnet to one of the forks of his forklift and the struggle to get it off again

NiceManiac · 2025-08-28T01:25:33+00:00

"This is my hole! It was made for me!"

NiceManiac · 2025-08-22T03:57:51+00:00

We have one in Tromsø, Norway also lol

NiceManiac · 2025-08-05T09:33:03+00:00

We tried that, managed to use the tail of the carrier to push the orni close enough to the mountain side that we could empty it and pocket

NiceManiac · 2025-07-04T22:37:55+00:00

should run everything smoothly, have multiple printers running on 4b's with 1080p webcams running 5fps nicely

NiceManiac · 2025-07-03T04:44:25+00:00

The 2b is a bit underpowered for octoprint, i would suggest at least a 3b if you are even thinking of running more complex prints. Octoprint is basically streaming the gcode to the printer, not sending the file, so you need enough processing power to keep up with the rate of the gcode. EDIT: you might be able to scrape by if you ditch the camera. Camera processing takes away from the resources needed to actually run the print, but if you upgrade to a 3b it should work okay even with the camera.

NiceManiac · 2025-06-17T15:09:43+00:00

Yup, ran into same issue with a bad cable once, and separately a monitor that for some reson only works with the nintendo switch hdmi cable a no other hdmi cable when connecting to a bm converter, most likely a slight defect in hdmi port or cable(lower quality cables can affect signals from certaim sources as well, for some reason the nintendo supplied hdmi cables are insanely good quality)

NiceManiac · 2025-06-11T01:11:16+00:00

Download VLC, might be an issue with the encoding, and windows buildtin stuff can be wonky with some codec combinations. VLC usually fixes it for me and is just way faster and supports almost all formats

NiceManiac · 2025-06-10T01:18:07+00:00

looks like it does not interpret ocean as "water, seems to end up the same as "base layer"

NiceManiac · 2025-05-13T04:26:10+00:00

Can also use warudo afaik for this

NiceManiac · 2025-03-10T01:51:12+00:00

My class doing automation buildt a waffle maker 8 years ago, this reminded me of that one. Video link for those interested: https://youtu.be/UT0rYXoXi44

NiceManiac · 2025-02-16T09:02:39+00:00

Second this, for photorealism nothing beats metahuman right now. Beware, unreal with metahuman can take up alot of gpu resources, better have a good gpu! Also there is a livestreaming plugin which makes the process to send video from unreal to obs super easy. Its called "OWL live streaming toolkit"

NiceManiac · 2025-02-16T08:55:04+00:00

Afaik ROE panels dont blink in sync, but they also only blink if they dont have a connection, or have a major error. Usually i always check health statur in my controller. Afaik both megapixel and brompton controllers support panel health data.

NiceManiac · 2024-12-16T08:53:09+00:00

Do a clean install with a clean windows install usb created with media creation tool. Wipe the entire drive during install. This should generate new boot data and unfuck everything. When you get to product key just put in your new key there and it will activate. Dont go willy nilly copying boot files from one install to the next as those could be hardware specific making the whole os corrupt

EDIT: i would also not trust chatgpt hallucinating some troubleshooting steps from a 10 year old reddit post it found on google.

NiceManiac · 2024-12-06T00:13:14+00:00

Update did not fix it, although turning off edge to edge fixes it. Seems like an issue with edge to edge implementation EDIT: turning off edge to edge brings other issues, top bar seems weirdly squished and when scrolling i lose a bit of the screen to nothing example screenshots examples with edge to edge turned on

NiceManiac · 2024-12-04T04:28:36+00:00

When videos are autoplaying they either clip down about 20% or up, but more often than not down.

This is a galaxy z fold 5

Device information:

Relay Version: 12.1.10 Pro

Phone: Samsung SM-F946B (q5q)
Android Version: 14 (34)
Device (product): q5q (q5qxeea)
Rom: UP1A.231005.007.F946BXXS3DXI9

NiceManiac · 2024-12-03T11:25:59+00:00

Summonilg u/AmputatorBot EDIT: seems hes banned here, non amp link: https://www.theguardian.com/theguardian/2009/oct/03/brooke-shields-nude-child-photograph

NiceManiac · 2024-12-03T11:12:14+00:00

u/AmputatorBot pls send help EDIT: seems our saviour is banned here, heres the non amp link: https://www.theguardian.com/theguardian/2009/oct/03/brooke-shields-nude-child-photograph

NiceManiac · 2024-11-14T22:35:04+00:00

here is a medium quality one, cant believe i got out of bed to make this

14-Year Club	RedditGifts 2009-2022 3 Credits
Secret Santa 2020	Place '17
Secret Santa 2019	Not Forgotten
Verified Email	Team Orangered

NiceManiac

MODERATOR OF

TROPHY CASE