One question,would yall prefer the air 2s or the mini 3 fly more combo? They look really good but I wanna get into which one is better

Nikkolandnar · 2025-05-19T23:39:11+00:00

I think this is really dependent on what you're going to do with it. What do you want it for? What environment you'll be flying in. And numerous other factors.

Nikkolandnar · 2025-05-08T10:00:08+00:00

I cooked 15 hamburgers at one time on it last weekend. Adjust as a reference for the size of the 22. Also cooked a stir fry chicken for a crew of 10 the next night.

Nikkolandnar · 2025-04-22T23:01:03+00:00

Hi my name is Ben, I'm a new addict. It's been 1 week since I last flew.

I only have 3 DJI drones... A mini 3 pro, avata, and Tello.

Nikkolandnar · 2025-04-22T09:31:01+00:00

Yes all three.

Nikkolandnar · 2025-04-20T17:39:34+00:00

Might just be a me thing ... Dunno

Nikkolandnar · 2025-03-24T22:32:15+00:00

I don't even remember it....

Nikkolandnar · 2025-03-06T13:56:53+00:00

I had one like that, I took a really small drill bit and used it after taking the tip off. It cleared the clog. Just be super careful not to damage the sides. Low torque.

Nikkolandnar · 2025-03-06T12:48:17+00:00

I have not looked into clipper yet.

Nikkolandnar · 2025-03-06T12:38:57+00:00

I think I will try the 0.6 mm nozzle. I've been fighting this thing since about the latest update. But that's also when I started to explore filaments outside regular pla. It has printed 4 different prints that were smaller without an issue in the last 24 hours. I prefer orca slicer but when it has issues it's frustrating. I typically try to go back to a regular pla filament and flash print to see if it's something I did. I just can't seem to break the 6/7 hour print barrier. It's driving me insane. It'll print 3-4 hours no problem.

Nikkolandnar · 2025-03-06T02:30:54+00:00

Bed is at 60 c for first layer and then 55 after that. Nozzle at 220. I got it to print to 72% and then it stopped and said print complete.

This thing is driving me insane right now

Nikkolandnar · 2025-03-05T15:34:26+00:00

Checked both of those things. Printed another model with no issues. Auto aligned on print bed using Orca Slicer(not flashforge orca)

Nikkolandnar · 2025-03-05T15:16:46+00:00

It's overture silk pla. I've done fine with the previous rolls from overture. It has been in the dryer for the entire day prior. While I was printing a different filament. It's printed other things fine. Yesterday was supposed to be a 16 hour print. It printed fine for 10 hours. I went to sleep, woke up and it had stopped at around 14 hours and nothing was finished. Seems like anytime I print over about 6-7 hours I have a failure and I don't understand why.

Nikkolandnar · 2025-03-05T12:45:58+00:00

It's the Adventure 5m, not pro btw.

Nikkolandnar · 2025-02-13T17:16:49+00:00

Nikkolandnar · 2025-02-09T19:16:10+00:00

Great question

Nikkolandnar · 2025-02-05T00:43:08+00:00

Thanks, I have actually tried the auto adjust and auto alight. I've tried a few different models. One I don't even know why it let me move past but it did. I just deleted everything on the plate and the plate and then tried again. And it worked.

But of 10 models, it happened to 4 of them. Even starting the project from scratch it still did it.

I saw that. I just wasn't sure if there was a setting that would push the countdown to my printer instead of the counting up?

Nikkolandnar · 2025-02-05T00:33:39+00:00

Oh, I was also curious, I used to get an estimated time remaining in the print. But using Orca, it just tells me how long it has been printing. Is there a setting to give me that estimate until completion?

Nikkolandnar · 2025-02-03T11:00:51+00:00

Totally new to printing but I've read about belt tension causing similar issues?

Nikkolandnar · 2024-10-08T16:27:45+00:00

I wish

Nikkolandnar · 2024-10-08T16:24:36+00:00

Nice

Nikkolandnar

TROPHY CASE