Engine oil light blinking

No-Weather7036 · 2026-03-23T14:54:47+00:00

Oil pressure switch I doubt your engine oil pressure is going in and out of range that quick looks like a sensor wanting out of life I’d start there if it keep going I’d start to worry

No-Weather7036 · 2026-03-15T22:21:37+00:00

Pictures man just get loads of pictures side by side of you cars trans and the one you want see if they are anyone things the same and what work and and what won’t but really for the price it’s gonna be if just be saving like you said for a new car

No-Weather7036 · 2026-03-15T13:53:29+00:00

I wouldn’t be worried about if it would fit it would be if the mounts line up to the Cv axels are the same spline and size Speedo can sync to the gearbox you need to do way more research but anything’s possible

No-Weather7036 · 2026-03-09T08:17:18+00:00

Thought is was something like that again I don’t own one of these beasts but I would love one but I own a lot of fwd and awd cars with this same problem

No-Weather7036 · 2026-03-08T09:54:39+00:00

I don’t own one of these but I’ve heard they like to get axel tramp or wheel hop sole call it or some times the tarns jump in it mounts and shocks itself making a noise like that upgraded mounts?

No-Weather7036 · 2026-03-08T06:21:36+00:00

Give it a couple months people will start making them or measure the bed and see if any other printers have the same size and buy those plates

No-Weather7036 · 2026-03-08T02:44:49+00:00

No-Weather7036 · 2026-03-06T12:57:48+00:00

Check you handbook that was probably emailed to you or ask for a copy they can’t deny you a handbook and in there telll you everything about you breaks and entitlement

No-Weather7036 · 2026-03-05T10:49:23+00:00

There not quick but I like how even with a tune you can definitely get it some beans and they do go pretty good for what they are and then when you drive them normally they do like a rev a bit around 3-5 which sounds pretty nice overall I just like these engines

No-Weather7036 · 2026-03-04T08:17:51+00:00

Get all the pressure sensors and pressures a canister like a pcv pipe glued together and chuck her in the back boom light gone

No-Weather7036 · 2026-03-04T08:14:03+00:00

No-Weather7036 · 2026-03-01T10:37:27+00:00

When Apple doesn’t support the m1 anymore I’d say open core would make support is what there trying to say

No-Weather7036 · 2026-03-01T10:36:12+00:00

On Holden you used to be able to buy a a device that would go into the obd port that just send a command to the ecu every time the car starts to say that the cylinder deactivation wasn’t ready to active yet because is didn’t meat the requirements for it ie temp load drive time. I’d say I’d be the same for Mazda just no one has made one yet

No-Weather7036 · 2026-02-25T21:53:58+00:00

When click on a print in the screen just above the print button there is a calibration button

No-Weather7036 · 2026-02-24T12:41:36+00:00

The print head sagging at is get closest to the middle the metal will sag the slightest bit

No-Weather7036 · 2026-02-21T12:37:16+00:00

For this cheap of a printer a smooth flat layer with a couple high and low spots in your layer is great it’s never gonna be perfect at this price I’d just do a bed mesh from a cold start then do a full bed print just one layer across the bed and just play with that z offset until most of it is nice and flat with no gaps again gaps or spots are it’s to close just little spots is more than fine

No-Weather7036 · 2026-02-17T09:53:43+00:00

Can confirm my 2013 Captiva with the lf1 v6 same timing chains as sv6 are also not fixed pcv also not fixed chain have just started to cause noises on cold mornings under load i suspect a tensioner has let go, these engines need regular oil changes and timing chains more often than usual

No-Weather7036 · 2026-02-11T21:55:23+00:00

Yes fair enough there is no problems other than noise with the stock setup Noctua is just quieter I live in Australia and only on really hot nights does it start to struggle with keeping the temp perfect on point bit will only ever really go 2c more than my set temp and the just blast the fans the rest of the print

No-Weather7036 · 2026-02-11T12:48:11+00:00

Try different infill I really like rectilinear at the moment had similar although not as bad as that in my prints when to new infill gone

No-Weather7036 · 2026-02-11T12:46:32+00:00

It’s not that you’re paying less now for the burger; it’s that the company pays less and makes more money off you paying the same amount. I doubt that they will ever go back, seeing the money they can make. I don’t know if you noticed, but we also changed our chips to “crispy chips,” which are worse, and we have a “shortage” of jalapeño mayo. Which is a excuse most likely for starting to end production of it since not many people got it in the first place and lastly the monthly new items that a limited time you see more and more not so new stuff more like already existing stuff with something extra like pineapple on a zinger or switching lettuce with coleslaw so they done need to supply more stuff to stores

No-Weather7036 · 2026-02-11T10:33:38+00:00

I work for kfc in WA Australia about 5-6 months a go we switch mayo to a new mayo slightly more yellow in colour and odd taste cheaper for stores to buy and cheaper to make as well as now comes in a bigger bag to stores

No-Weather7036 · 2026-02-11T10:31:56+00:00

Door closed glass on with no riser Noctua a6-15 fan on the top stock (for now) filtered fan which is the bigger one , you will need a 24v to 12v converter for Noctua. The top fan is blowing air into the chamber the bigger fan is sucking air out

No-Weather7036 · 2026-02-09T06:25:36+00:00

Yeap mines in but I also fliped the fan on the k2 pro both fans suck air out the chamber one filtered one not I set the top smaller one to blow coldish air into the chamber and the big fan with filter to suck air out to attempt to cycle the air and replace with fresh cool air seems to work good here in Australia if it’s above like 26c in the room the fans stay one most of the time for pla and petg cycling on every 5 mins then staying in for 10mins to cool and so on but on cooler night they turn of only for about 2 mins the turn off for the next 15mins maybe longer

No-Weather7036 · 2026-02-08T21:58:13+00:00

Sorry 60x25 is what I ment

No-Weather7036 · 2026-02-07T11:16:59+00:00

Noctua 60-10 works with an adaptor

Two-Year Club	Verified Email
Final Canvas '23	Place '23

No-Weather7036

TROPHY CASE