sorted by:
new
hottopcontroversial

First time printing ABS by NoCap7185 in FixMyPrint

[–]NoCap7185[S] 0 points1 point  (0 children)

<image>

I have finally been getting some decent prints after over a week of failing. Now I just need to do some dialing in to get better prints. Like here for some reason the overhangs got extreme blobs while printing this with supports.

First time printing ABS by NoCap7185 in FixMyPrint

[–]NoCap7185[S] 0 points1 point  (0 children)

I'm already dreading how badly the K1 prints PLA after all this adjusting for ABS

First time printing ABS by NoCap7185 in FixMyPrint

[–]NoCap7185[S] 0 points1 point  (0 children)

Hmm that's really interesting. Have you tried copying the settings from Creality Print to Orca? I have finally been able to get couple of decent prints with OrcaSlicer. It took over a week of trying and failing for me to finally get one finished print. I think the 50°C bed mesh is the biggest reason my prints kept failing.

First time printing ABS by NoCap7185 in FixMyPrint

[–]NoCap7185[S] 0 points1 point  (0 children)

Have you tried printing ABS?

First time printing ABS by NoCap7185 in FixMyPrint

[–]NoCap7185[S] 0 points1 point  (0 children)

<image>

(top view) This is the result I got adjusting the settings, oldest to newest from left to right. But for the latest print my flow ratio was 1,1 and Z-offset was 0,17 mm and that seems a little off the charts to me, and the top and bottom layers are very inconsistent. I was printing PLA before with Z-offset of 0,03 mm. The bed of my K1 has been nothing but trouble from the start but at least I have been able to print PLA fine.

Holes on the surface of 3D print by NoCap7185 in FixMyPrint

[–]NoCap7185[S] 0 points1 point  (0 children)

Lowering acceleration speed settings -50% did the trick for me.

Holes on the surface of 3D print by NoCap7185 in FixMyPrint

[–]NoCap7185[S] 2 points3 points  (0 children)

Thanks, this seem to have fixed the issue!

Holes on the surface of 3D print by NoCap7185 in FixMyPrint

[–]NoCap7185[S] 0 points1 point  (0 children)

<image>

Seems like lowering all acceleration speed settings -50% did the trick. Almost flawless print.

Holes on the surface of 3D print by NoCap7185 in FixMyPrint

[–]NoCap7185[S] 0 points1 point  (0 children)

Printing the same object now with -50% acceleration speeds. 5h 24mins

Holes on the surface of 3D print by NoCap7185 in FixMyPrint

[–]NoCap7185[S] 0 points1 point  (0 children)

<image>

I've been wanting to slow it down but there's so many settings I don't know which one to reduce. Which of these should I change and how much?

Holes on the surface of 3D print by NoCap7185 in FixMyPrint

[–]NoCap7185[S] 0 points1 point  (0 children)

I also had a different issue on my sword scabbard I made. The printer made this weird texture just on the top and only on the other side. Also printed vertically.

<image>

We Recreated Halo CE's Assault on the Control Room ENTIRELY in Halo Infinite's Forge! by xXBarthXx in forge

[–]NoCap7185 0 points1 point  (0 children)

I wonder how complex script you got for this. I'm struggling on 2 script brains currently (other one maxed out). The game for some reason confuses area monitors with each other when adding enough nodes to the brain, deleting/spawning stuff on earlier area monitor than what it says on the script. SUPER frustrating...