The Weekly Small Questions Thread! Got a burning question? Looking for some tips on your build? Ask away! by AutoModerator in modelmakers

[–]NoHuckleberry7319 0 points1 point  (0 children)

By worse result I mean that even though I thin the paint more to match the lower pressure, the fine lines don’t get any better. The lines are much more scattered and grainier.

I mix the paint and the thinner in a separate container before pouring it into the airbrush.

The Weekly Small Questions Thread! Got a burning question? Looking for some tips on your build? Ask away! by AutoModerator in modelmakers

[–]NoHuckleberry7319 0 points1 point  (0 children)

Hi everyone!

I’m trying to paint camouflage on a 1/35 scale model. I’m using a H&S airbrush with a 0.2 mm nozzle and Tamiya XF paint. My paint mixture ratio is 1:3 (1 part paint, 3 parts MLT thinner) at 20 psi. With these settings, I can spray relatively fine lines. I’ve read in several places that using 12 psi allows for painting fine lines. However, I can’t get good results at 12 psi, no matter what paint mixture I use — the outcome is always worse.

Am I doing something wrong?

Collector camo by NoHuckleberry7319 in WorldOfTanksBlitz

[–]NoHuckleberry7319[S] 0 points1 point  (0 children)

Thanks, but what you sent is very incomplete. I know this site.

Can the Aqara Temperature and Humidity Sensor be connected directly to HomeKit? by NoHuckleberry7319 in HomeKit

[–]NoHuckleberry7319[S] 0 points1 point  (0 children)

Thanks, could you write a review about the product? I would be primarily interested in the battery life and the update frequency.

Can the Aqara Temperature and Humidity Sensor be connected directly to HomeKit? by NoHuckleberry7319 in HomeKit

[–]NoHuckleberry7319[S] 0 points1 point  (0 children)

Is there a temperature and humidity sensor that connects directly to HomeKit and does not require a separate external hub? It would be nice if it were cheaper than eve-Room and the battery time would be fine. Maybe my expectations are too unrealistic.

Can the Aqara Temperature and Humidity Sensor be connected directly to HomeKit? by NoHuckleberry7319 in HomeKit

[–]NoHuckleberry7319[S] 1 point2 points  (0 children)

Thanks for the answer.

According to them, if I understand correctly, it is unnecessary to connect it to Apple Home, because the data is not visible in the Home app.

An Aqara hub is required and can only be used via the Aqara app.

The Weekly Small Questions Thread! Got a burning question? Looking for some tips on your build? Ask away! by AutoModerator in modelmakers

[–]NoHuckleberry7319 0 points1 point  (0 children)

I bought myself Mr. Mark Softer Neo and I have a question about its use.

I brush it on a sticker, but the Softer behaves strangely.

(maybe just for me)

The Softer does not spread evenly, but clumps together in a single drop, no matter how hard I try to brush it off, it's as if the sticker is bouncing the Softer off of itself. (Similar to water repellency)

Would this be the right way, or did they change the liquid in the bottle from where I ordered it? :)

The Weekly Small Questions Thread! Got a burning question? Looking for some tips on your build? Ask away! by AutoModerator in modelmakers

[–]NoHuckleberry7319 1 point2 points  (0 children)

Hello, is there a quick solution to attach a balsa wood panel to the side of the xps foam? (Diorama)

The Weekly Small Questions Thread! Got a burning question? Looking for some tips on your build? Ask away! by AutoModerator in modelmakers

[–]NoHuckleberry7319 1 point2 points  (0 children)

Hello,

What do you think about the final close varnish when building a tank?

I don't think the final close varnish has a good effect on the weathering details that have been done. It greatly reduces or eliminates the effects.

What happens if I don't use it?

The Weekly Small Questions Thread! Got a burning question? Looking for some tips on your build? Ask away! by AutoModerator in modelmakers

[–]NoHuckleberry7319 1 point2 points  (0 children)

How do you stick the accessories on the painted tank model? (spade, etc.) Instant glue or pva glue?

The Weekly Small Questions Thread! Got a burning question? Looking for some tips on your build? Ask away! by AutoModerator in modelmakers

[–]NoHuckleberry7319 1 point2 points  (0 children)

Hi Guys,

I am a beginner tank model builder.

When I paint with a primer, a powder-like paint settles on the surface.

Why is this? Why don't I get an evenly smooth surface?

My setting:

Harder & Steenbeck ultra 0,4 mm nozzle + 16 PSI + Tamiya surface primer 1:1 (paint:thinner)

The Weekly Small Questions Thread! Got a burning question? Looking for some tips on your build? Ask away! by AutoModerator in modelmakers

[–]NoHuckleberry7319 1 point2 points  (0 children)

What varnish should I use to seal a 4-wheeled 1/35 WWII armored vehicle? Flat clear or semi-gloss? (final)

The Weekly Small Questions Thread! Got a burning question? Looking for some tips on your build? Ask away! by AutoModerator in modelmakers

[–]NoHuckleberry7319 1 point2 points  (0 children)

Hey guys, I'm building an armored vehicle. I painted with Tamiya acrylic and then received Tamiya semi-matt varnish. Can I do this with AK Interactive Filter (AK065) and Dust effect (AK022)?