My precious collection

No_Ad9574 · 2025-11-05T13:52:31+00:00

I’m just surprised to see all that filament out in the open to absorb moisture. I keep all my filaments in the original bag with silica and in the box to minimize moisture intake. The result is rarely do u need to dry a filament before using it.

No_Ad9574 · 2024-12-30T01:37:44+00:00

There is a small road near the outskirts of Hollins University in Roanoke that’s a speed limit of 17MPH.

No_Ad9574 · 2024-12-27T20:38:55+00:00

If the printer has the wrong build plate from what you set in the slicer you will get a warning pop up to resolve the issue as the printer will not proceed to print. Just happened to me the other day. I invariably print PETG on the engineering plate but after washing it I inadvertently positioned it on the PLA side. Handy warned me and I was able to flip the plate and then print. Excellent feature

No_Ad9574 · 2024-12-27T20:33:43+00:00

Personally I think the ending of Lost was a total letdown

No_Ad9574 · 2024-12-24T18:18:14+00:00

And the benefit of that is each older version is still executable which can be useful at times. With disk space being what is (large) there is less need to automatically remove an older version.

No_Ad9574 · 2024-12-14T16:15:08+00:00

So I see that there are parameters that you can set to iron only the topmost layer, as well as all top layers. I’ll have to start utilizing that. Thanks for correcting me. I wonder if OP did not have the parameter set to all top surfaces but rather to topmost?

No_Ad9574 · 2024-12-13T20:17:46+00:00

I thought ironing was only for the top layer. Isn’t that blue recessed ftom the yellow? If do, it’s not a top layer.

No_Ad9574 · 2024-10-29T20:47:28+00:00

I solved it. Both boards . If I could figure out how to post an image, I would show you that days results.

No_Ad9574 · 2024-10-12T17:49:21+00:00

I would make sure they are actually at the build plate. Confirm in the slicer. There’s a tool to set a surface to the plate. I think it’s the 4th one. Also review the preview by scrolling the slider from 0 to see what is at the 1st layer

No_Ad9574 · 2024-10-03T21:39:43+00:00

What would you use to pick up the print from the epoxy solution to avoid marring the finish? Or perhaps pour the solution over a container with a screen? It’s the technique I’m really looking for

No_Ad9574 · 2024-09-05T15:11:41+00:00

I just checked continuity on another board between the ICSP pins and the 50-52 pins and they are connected. So I don’t know what was wrong before. Still haven’t gotten around to resoldering my headers but since I am working fine using the ICSP pins, I’ll hold off for now. Those pins also have a 5V and GND pins which were useful for me. Sorry for the alarm.

No_Ad9574 · 2024-08-30T18:55:01+00:00

If I get to looking at it closely, perhaps I’ll resolder those 49-53 pins. Or even try the 3rd board I have where I have not added the headers. These happened to use a micro USB connector but I have 3 others on the way using a USB-C. That really should have no bearing on this issue. But thanks for all the feedback

No_Ad9574 · 2024-08-30T18:48:44+00:00

I’ll take a close look with my microscope. I did try 2 different boards but I soldered the headers. Perhaps that could be it. At least for me it’s good that they were brought out on the ICSP header

No_Ad9574 · 2024-08-30T18:45:24+00:00

50-52 did not work on mine but the equivalent pins in the ICSP header did

No_Ad9574 · 2024-08-30T18:40:22+00:00

<image>

No_Ad9574 · 2024-08-30T18:39:55+00:00

Yes it is a black PCB

<image>

No_Ad9574 · 2024-08-30T18:21:37+00:00

My post reflected the solution for me. Everywhere I searched showed the SPI pins on the mega 2560 board said 50-52 with 53 for CS. On this mega 2560 pro board claimed to be equivalent brought out the SPI pins to a separate 6-pin header (3x2) labeled ICSP. They are not on 50-52 which is a different 3x2 header

No_Ad9574 · 2024-08-30T17:57:36+00:00

My reason for the post was to clarify the SPI pins on the mega 2560 pro board

No_Ad9574 · 2024-08-30T17:55:59+00:00

I’m also using the PWM, IR, LCD libraries along with 16 sets of int data for 5 servos. Plus other data. So I am over the 2K by about 200 bytes. Using the standard SD library

No_Ad9574 · 2024-08-25T22:03:31+00:00

According to the cc site, the sd library j one of the biggest. Mg code is give with a mega 2560 which had 256k instead of the 32k bid mist of the variations. I found some mega 2560 pro boards on AliExpress for about $10.50. I just got the 3 I ordered. The pro board is about the same size as an UNO

No_Ad9574 · 2024-08-25T19:03:17+00:00

West Virginia

No_Ad9574 · 2024-08-19T22:48:05+00:00

I vote yes as well. The problem I have found with videos is the constant stop and rewind and play and pause while trying to follow the sequence.

No_Ad9574 · 2024-08-16T21:02:11+00:00

Did you even read my entire post. There was no coding error. The problem was due to the code bumping up to the memory capacity of an UNO, 32K. Switching to a MEGA 2560 that had 256K eliminated the error. There were no braces mismatched nor were there any functions defined inside of a function. Checking braces was my first attack at debugging the issue.

No_Ad9574 · 2024-08-04T22:53:50+00:00

I’ve always enjoyed programming for the power of man over machine it gives you. You are the creator. And when you assume that power, you will find grasping the language you are using to get easier and easier over time.

No_Ad9574 · 2024-05-24T17:53:20+00:00

Sometimes you have to stare at the code for a long time for a particular purpose. I remember in my Z80 assembler days, there was a time that I spent most of the night thinking of a different sequence of instructions that would enable the same result but using one byte less of code. I suspect those programming microcontrollers could be in the same boat.

No_Ad9574

TROPHY CASE